Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235968 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Touch Sensor Circuit  


DESCRIPTION

When the power back door ECU receives a jam signal from the touch sensor while the power back door closer is operating, the ECU reverses the back door operation and opens the door.

WIRING DIAGRAM

B165200E49
4.75,2.99 6.49,3.219 1.74,0.229 10 false O30 4.76,3.146 6.479,3.51 1.719,0.365 10 false Power Back Door Drive Unit (Power Back Door ECU) 5.094,2.771 6.833,3 1.74,0.229 10 false OSE 5.094,1.854 6.833,2.083 1.74,0.229 10 false OSR 5.094,0.688 6.833,0.917 1.74,0.229 10 false OSL 4.833,0.573 6.573,0.802 1.74,0.229 10 false 15 4.844,1.75 6.583,1.979 1.74,0.229 10 false 13 4.833,2.656 6.573,2.885 1.74,0.229 10 false 14 3.667,1.729 5.406,1.958 1.74,0.229 10 false 1 3.656,0.563 5.396,0.792 1.74,0.229 10 false 1 2.135,0.573 3.875,0.802 1.74,0.229 10 false 2 2.135,1.729 3.875,1.958 1.74,0.229 10 false 2 1.99,2.292 3.729,2.521 1.74,0.229 10 false V14 2,2.448 4.583,2.615 2.583,0.167 10 false Power Back Door Sensor RH 1.969,1.25 3.76,1.417 1.792,0.167 10 false Power Back Door Sensor LH 1.969,1.083 4.552,1.25 2.583,0.167 10 false V15

PROCEDURE

1.READ VALUE USING TECHSTREAM (POWER BACK DOOR TOUCH SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door / Data List /


e.

According to the display on the Techstream, read the Data List.

Back Door
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PBD Touch Sen L Power back door touch sensor LH signal / ON or OFF ON: Power back door touch sensor LH is pressed
OFF: Power back door touch sensor LH is not pressed
-
PBD Touch Sen R Power back door touch sensor RH signal / ON or OFF ON: Power back door touch sensor RH is pressed
OFF: Power back door touch sensor RH is not pressed
-

OK:

The display is as specified in the normal condition.




OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

2.INSPECT POWER BACK DOOR TOUCH SENSOR
2.INSPECT POWER BACK DOOR TOUCH SENSOR
a.
B443312E01
0.188,2.865 2.646,3.208 2.458,0.344 10 false Component without hamess connected: (Power Back Door Touch Sensor) 2.51,0.365 3.365,0.552 0.854,0.188 10 false Not Pressed 2.698,1.823 3.271,2.01 0.573,0.188 10 false Pressed

Remove the power back door touch sensor (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR(for LH Side)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Not pressed 950 to 1050 Ω
1 - 2 Pressed Below 100 Ω



c.

Reinstall the power back door touch sensor.



OK

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR TOUCH SENSOR - POWER BACK DOOR DRIVE UNIT AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR TOUCH SENSOR - POWER BACK DOOR DRIVE UNIT AND BODY GROUND)
a.
U153374E02
1.042,4.271 0.844,3.448 0.844,3.448 0.708,3.448 true 1.146,4.271 1.344,3.448 1.344,3.448 1.479,3.448 true 0.281,0.021 2.75,0.385 2.469,0.365 10 false Front view of wire hamess connector: (to Power Back Door Touch Sensor LH) 0.75,1.719 1.042,1.885 0.292,0.167 10 false V15 0.25,4.083 0.542,4.25 0.292,0.167 10 false O30 0.281,2.344 2.75,2.708 2.469,0.365 10 false Front view of wire hamess connector: (to Power Back Door ECU) 0.375,3.365 0.708,3.531 0.333,0.167 10 false OSE 1.531,3.365 1.844,3.521 0.313,0.156 10 false OSL

LH Side

i.

Disconnect the V15 sensor connectors.


ii.

Disconnect the O30 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V15-1 - O30-15 (OSL) Always Below 1 Ω
V15-2 - O30-14 (OSE) Always Below 1 Ω
V15-1 - Body ground Always 10 kΩ or higher
V15-2 - Body ground Always Below 1 Ω




b.
U153375E02
0.917,4.271 0.719,3.448 0.719,3.448 0.583,3.448 true 1.042,4.271 1.24,3.448 1.24,3.448 1.375,3.448 true 0.24,0.073 2.74,0.438 2.5,0.365 10 false Front view of wire hamess connector: (to Power Back Door Touch Sensor RH) 0.74,1.708 1.031,1.875 0.292,0.167 10 false V14 0.25,4.083 0.542,4.25 0.292,0.167 10 false O30 0.24,2.344 2.708,2.708 2.469,0.365 10 false Front view of wire hamess connector: (to Power Back Door ECU) 0.188,3.375 0.531,3.542 0.344,0.167 10 false OSR 1.427,3.365 1.74,3.521 0.313,0.156 10 false OSE

RH Side

i.

Disconnect the V14 sensor connectors.


ii.

Disconnect the O30 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-1 - O30-13 (OSR) Always Below 1 Ω
V14-2 - O30-14 (OSE) Always Below 1 Ω
V14-1 - Body ground Always 10 kΩ or higher
V14-2 - Body ground Always Below 1 Ω



iv.

Reconnect the sensor connectors.


v.

Reconnect the ECU connector.




OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR