Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM27L0U _59 Vehicle Exterior _049351 WIPER / WASHER _0235977 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the volume of washer fluid decreases to below a certain level (when the washer fluid level warning switch is turned ON), the combination meter assembly warns the driver through the master warning light illumination and the warning message on the multi-information display*1, or the washer warning light illumination*2.

HINT:

*1: w/ Multi-information Display

*2: w/o Multi-information Display


WIRING DIAGRAM

E146596E03
5.292,3.054 5.573,3.209 0.282,0.156 10 H37 5.292,3.223 6.500,3.384 1.208,0.161 10 Combination Meter 5.543,1.893 5.944,2.049 0.401,0.156 10 WLVL 5.253,1.791 5.445,1.943 0.191,0.152 10 10 2.226,2.278 2.496,2.434 0.269,0.156 10 A31 2.226,2.446 4.438,2.627 2.212,0.182 10 Washer Fluid Level Warning Switch 2.736,1.894 2.853,2.056 0.117,0.162 10 E 3.476,1.894 3.593,2.056 0.117,0.162 10 S 3.672,1.793 3.778,1.951 0.106,0.158 10 1 2.541,1.793 2.647,1.951 0.106,0.158 10 2

PROCEDURE

1.READ VALUE USING TECHSTREAM (WASHER FLUID LEVEL WARNING SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the Techstream, read the Data List.


Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Washer Switch Washer fluid level warning switch / ON or OFF ON: Washer jar and tank is empty
OFF: Washer jar and tank is full
-

OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
2.INSPECT WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
a.
E162511E02
0.196,0 2.678,0.343 2.482,0.343 10 Component without harness connected: (Washer Fluid Level Warning Switch) 2.451,2.653 2.584,2.819 0.133,0.166 10 S 0.832,2.653 0.974,2.823 0.142,0.170 10 E 0.986,2.644 1.425,2.197 false 2.445,2.634 1.983,2.172 false 0.986,2.644 1.425,2.197 false 2.445,2.634 1.983,2.172 false

Disconnect the A31 washer fluid level warning switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (S) - 2 (E) Washer jar is empty Below 1 Ω
Washer jar is full 10 kΩ or higher



c.

Reconnect the washer fluid level warning switch connector.



OK

3.CHECK HARNESS AND CONNECTOR (WASHER FLUID LEVEL WARNING SWITCH - COMBINATION METER)

NG

REPLACE WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WASHER FLUID LEVEL WARNING SWITCH - COMBINATION METER)
a.
U153993E02
1.49,1.76 1.146,2.021 false 2.344,2.021 1.969,1.76 false 1.667,3.646 1.375,4.125 false 0.156,2.365 2.51,2.708 2.354,0.344 10 false Front view of wire harness connector: (to Combination Meter) 1.135,4.135 1.531,4.302 0.396,0.167 10 false WLVL 0.156,0.021 2.542,0.365 2.385,0.344 10 false Front view of wire harness connector: (to Washer Fluid Level Warning Switch) 1,2.021 1.115,2.167 0.115,0.146 10 false S 2.375,2.021 2.49,2.167 0.115,0.146 10 false E 3.021,3.052 3.292,3.229 0.271,0.177 10 false H37 3.021,1.115 3.281,1.292 0.26,0.177 10 false A31

Disconnect the A31 washer fluid level warning switch connector.


b.

Disconnect the H37 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-1 (S) - H37-10 (WLVL) Always Below 1 Ω
A31-1 (S) or H37-10 (WLVL) - Body ground Always 10 kΩ or higher
A31-2 (E) - Body ground Always Below 1 Ω



d.

Reconnect the washer fluid level warning switch connector.


e.

Reconnect the combination meter connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR