The main body ECU receives light control switch, dimmer switch and front fog light switch information signals from the headlight dimmer switch.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List /
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Dimmer SW | Dimmer switch signal / ON or OFF | ON: Dimmer switch ON
OFF: Dimmer switch OFF |
- |
| Passing Light SW | Passing light switch signal / ON or OFF | ON: Passing light switch ON
OFF: Passing light switch OFF |
- |
| Front Fog Light SW | Front fog light switch signal / ON or OFF | ON: Front fog light switch ON
OFF: Front fog light switch OFF |
- |
| Auto Light SW | Auto light switch signal / ON or OFF | ON: Auto light switch ON
OFF: Auto light switch OFF |
- |
| Head Light SW (Head) | Headlight switch signal / ON or OFF | ON: Headlight switch ON
OFF: Headlight switch OFF |
- |
| Head Light SW (Tail) | Taillight switch signal / ON or OFF | ON: Taillight switch ON
OFF: Taillight switch OFF |
- |
When combination light switch operation is performed, the result will be the same as above.
OK
NG
Remove the headlight dimmer switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 18 (T) - 12 (EL) | Light control switch TAIL | Below 1 Ω |
| Light control switch HEAD | Below 1 Ω | |
| 20 (H) - 12 (EL) | Light control switch HEAD | Below 1 Ω |
| 19 (A) - 12 (EL) | Light control switch AUTO | Below 1 Ω |
| 4 (BFG) - 3 (LFG) | Front fog light switch ON | Below 1 Ω |
| 17 (HF) - 12 (EL) | Dimmer switch High | Below 1 Ω |
| 11 (HU) - 12 (EL) | Dimmer switch Low | Below 1 Ω |
Reinstall the headlight dimmer switch assembly.
OK
NG
Disconnect the H11 headlight dimmer switch assembly connector.
Disconnect the H3, H4 and DD main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H11-4 (BFG) - H3-28 (FFOG) | Always | Below 1 Ω |
| H11-19 (A) - H4-21 (A) | Always | Below 1 Ω |
| H11-20 (H) - H3-17 (HEAD) | Always | Below 1 Ω |
| H11-18 (T) - H4-23 (TAIL) | Always | Below 1 Ω |
| H11-17 (HF) - H4-13 (HF) | Always | Below 1 Ω |
| H11-11 (HU) - DD-13 (HU) | Always | Below 1 Ω |
| H11-4 (BFG) - Body ground | Always | 10 kΩ or higher |
| H11-19 (A) - Body ground | Always | 10 kΩ or higher |
| H11-20 (H) - Body ground | Always | 10 kΩ or higher |
| H11-18 (T) - Body ground | Always | 10 kΩ or higher |
| H11-17 (HF) - Body ground | Always | 10 kΩ or higher |
| H11-11 (HU) - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H11-12 (EL) - Body ground | Always | Below 1 Ω |
| H11-3 (LFG) - Body ground | Always | Below 1 Ω |
Reconnect the headlight dimmer switch assembly connector.
OK
NG