Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM27L0U _59 Vehicle Exterior _049352 LIGHTING (EXT) _0235988 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Turn Signal Light Circuit  


DESCRIPTION

The turn signal flasher receives a turn signal switch signal from the headlight dimmer switch, and illuminates the front turn signal light, outer rear view mirror and rear combination light.

WIRING DIAGRAM

E161598E02
4.292,0.278 5.059,0.433 0.767,0.154 10 TURN-HAZ 4.466,0.713 4.860,0.863 0.394,0.150 10 LH-IG 2.444,0.145 3.242,0.321 0.798,0.177 10 from Battery 1.897,0.588 3.287,0.764 1.390,0.177 10 from IG1 No. 1 Relay 0.949,1.635 2.621,1.802 1.672,0.167 10 Front Turn Signal Light LH 3.795,2.073 5.466,2.240 1.672,0.167 10 Front Turn Signal Light RH 0.776,3.505 2.230,3.841 1.455,0.336 10 Outer Rear View Mirror Assembly LH* 0.776,2.639 2.237,2.954 1.461,0.316 10 Outer Rear View Mirror Sub-Assembly LH* 0.665,4.983 2.202,5.310 1.537,0.327 10 Rear Combination Light Assembly LH 3.861,3.946 5.316,4.283 1.455,0.336 10 Outer Rear View Mirror Assembly RH* 3.887,3.1 5.348,3.416 1.461,0.316 10 Outer Rear View Mirror Sub-Assembly RH* 3.785,5.349 5.322,5.676 1.537,0.327 10 Rear Combination Light Assembly RH 5.848,5.851 7.121,6.194 1.273,0.343 10 Turn Signal Flasher Assembly 0.377,6.211 2.144,6.367 1.767,0.156 10 *: w/ Side Turn Signal Light 5.963,0.057 6.071,0.212 0.108,0.155 10 1 6.163,0.164 6.301,0.317 0.138,0.153 10 B 5.966,0.472 6.079,0.625 0.113,0.153 10 3 6.159,0.592 6.332,0.760 0.173,0.168 10 IG 5.868,1.052 6.071,1.210 0.203,0.158 10 10 6.162,1.164 6.551,1.332 0.389,0.168 10 LTRN 5.855,1.418 6.063,1.575 0.208,0.158 10 17 6.167,1.535 6.586,1.688 0.419,0.153 10 RTRN 5.943,2.293 6.060,2.451 0.118,0.158 10 2 6.17,2.407 6.368,2.585 0.198,0.178 10 LL 5.95,2.752 6.060,2.912 0.110,0.160 10 8 6.158,2.869 6.376,3.037 0.218,0.168 10 LR 5.851,5.699 6.140,5.847 0.289,0.148 10 H39 5.953,4.906 6.055,5.074 0.103,0.168 10 4 6.167,5.045 6.295,5.202 0.128,0.158 10 E 0.949,1.481 1.232,1.651 0.282,0.170 10 A15 1.079,1.055 1.181,1.223 0.103,0.168 10 2 2.259,1.055 2.366,1.207 0.108,0.153 10 3 3.905,1.443 4.008,1.611 0.103,0.168 10 2 5.085,1.443 5.193,1.596 0.108,0.153 10 3 0.787,3.351 1.005,3.509 0.218,0.158 10 M5 0.419,2.293 0.532,2.461 0.113,0.168 10 3 2.36,2.293 2.468,2.451 0.108,0.158 10 4 3.486,2.739 3.599,2.907 0.113,0.168 10 3 5.427,2.739 5.534,2.897 0.108,0.158 10 4 3.861,3.78 4.059,3.933 0.198,0.153 10 L6 0.722,4.328 0.828,4.487 0.106,0.159 10 2 1.941,4.328 2.054,4.496 0.113,0.168 10 1 0.665,4.812 0.954,4.975 0.289,0.163 10 O23 3.797,4.703 3.903,4.862 0.106,0.159 10 2 5.017,4.703 5.129,4.871 0.113,0.168 10 1 3.796,5.188 4.085,5.351 0.289,0.163 10 O22 1.546,4.366 1.860,4.524 0.314,0.158 10 TRN 0.912,4.366 1.045,4.519 0.133,0.153 10 E 4.625,4.739 4.940,4.898 0.314,0.158 10 TRN 3.992,4.739 4.125,4.892 0.133,0.153 10 E 2.072,1.053 2.195,1.196 0.123,0.143 10 B 1.254,1.053 1.387,1.202 0.133,0.148 10 E 4.885,1.461 5.008,1.604 0.123,0.143 10 B 4.067,1.461 4.200,1.609 0.133,0.148 10 E 5.205,2.771 5.328,2.914 0.123,0.143 10 B 3.684,2.771 3.817,2.919 0.133,0.148 10 E 2.13,2.338 2.252,2.481 0.123,0.143 10 B 0.589,2.338 0.722,2.486 0.133,0.148 10 E 3.8,1.897 4.083,2.067 0.282,0.170 10 A16

PROCEDURE

1.CHECK TURN SIGNAL LIGHT
a.

Check that the turn signal lights blink.

Result
Result Proceed to
All turn signal lights do not blink A
Only front turn signal light does not blink B
Only rear combination light does not blink C
Only door mirror foot light does not blink* D

*: w/ Side turn signal light.




A

2.INSPECT FUSE (LH-IG, TURN-HAZ)

B

4.INSPECT FRONT TURN SIGNAL LIGHT BULB

C

6.INSPECT REAR TURN SIGNAL LIGHT BULB

D

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
2.INSPECT FUSE (LH-IG, TURN-HAZ)
a.

Remove the LH-IG fuse from the main body ECU.

E344950E01
1.552,2.396 1.76,1.844 false 5.854,1.365 5.979,0.833 false 0.104,0.063 2.333,0.302 2.229,0.24 12 false Engine Room Relay Block: 4.01,0.052 6.24,0.292 2.229,0.24 12 false Main Body ECU: 1.208,2.427 2.021,2.656 0.813,0.229 10 false TURN-HAZ 5.667,1.427 6.479,1.656 0.813,0.229 10 false LH-IG


b.

Remove the TURN-HAZ fuse from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LH-IG fuse Always Below 1 Ω
TURN-HAZ fuse Always Below 1 Ω



d.

Reinstall the LH-IG and TURN-HAZ fuses.



OK

3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY, IGNITION SWITCH, BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY, IGNITION SWITCH, BODY GROUND)
a.
U154013E01
0.031,0 2.432,0.350 2.401,0.350 10 Front view of wire harness connector: (to Turn Signal Flasher Assembly) 1.56,1.312 1.874,1.468 0.313,0.156 10 H39 0.495,2.727 0.706,2.887 0.211,0.161 10 B 1.772,2.841 1.984,3.002 0.211,0.161 10 E 1.177,2.933 1.388,3.094 0.211,0.161 10 IG 1.017,2.241 0.581,2.715 false 1.591,2.286 1.79,2.841 false

Disconnect the H39 turn signal flasher assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H39-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H39-1 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H39-4 (E) - Body ground Always Below 1 Ω



d.

Reconnect the turn signal flasher assembly connector.



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT TURN SIGNAL LIGHT BULB
a.

Temporarily replace the front turn signal light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the front turn signal light turn on.

OK:

Front turn signal light turn on




OK

END

NG

5.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
U153976E01
1.689,1.726 1.093,1.91 false 0.95,1.836 1.073,2.020 0.123,0.184 10 E 0.04,2.154 2.424,2.511 2.384,0.357 10 Front view of wire harness connector: (to Turn Signal Flasher Assembly) 0.205,3.406 0.507,3.557 0.302,0.151 10 H39 0.04,0.011 2.401,0.368 2.361,0.357 10 Front view of wire harness connector: (to Front Turn Signal Light) 0.186,1.132 0.453,1.284 0.267,0.151 10 A15 1.06,3.68 1.024,4.173 false 0.801,4.173 1.262,4.329 0.461,0.156 10 LTRN 2.39,1.877 2.581,2.089 0.191,0.211 10 B 1.987,1.742 2.36,1.946 false 0.689,1.13 0.840,1.280 0.151,0.149 10 *1 0.186,1.528 0.453,1.679 0.267,0.151 10 A16 0.689,1.526 0.840,1.675 0.151,0.149 10 *2 2.838,1.213 3.263,1.371 0.425,0.158 10 *1: LH 2.838,1.563 3.285,1.730 0.446,0.167 10 *2: RH 2.231,3.699 2.195,4.193 false 1.972,4.193 2.433,4.349 0.461,0.156 10 RTRN

a.

for LH:

i.

Disconnect the A15 Front turn signal light LH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-3 (B) - H39-10 (LTRN) Always Below 1 Ω
A15-2 (E) - Body ground Always Below 1 Ω
A15-3 (B) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the Front turn signal light LH connector.



b.

for RH:

i.

Disconnect the A16 Front turn signal light RH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-3 (B) - H39-17 (RTRN) Always Below 1 Ω
A16-2 (E) - Body ground Always Below 1 Ω
A16-3 (B) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the Front turn signal light RH connector.




OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR TURN SIGNAL LIGHT BULB
a.

Temporarily replace the rear turn signal light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the rear turn signal light turn on.

OK:

Rear turn signal light turn on.




OK

END

NG

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER, BODY GROUND)
U154074E02
1.208,3.771 0.646,4.25 false 2.229,3.771 2.792,4.198 false 1.583,1.958 1.365,2.104 false 1.865,1.969 2.073,2.104 false 0.104,0.198 2.531,0.854 2.427,0.656 10 false Front view of wire harness connector: (to Rear Combination Light Assembly) 0.094,2.281 2.479,2.979 2.385,0.698 10 false Front view of wire harness connector: (to Turn Signal Flasher Assembly) 0.448,1.365 0.74,1.521 0.292,0.156 10 false O23 0.885,1.344 1.125,1.5 0.24,0.156 10 false *1 0.448,1.802 0.74,1.958 0.292,0.156 10 false O22 0.885,1.771 1.125,1.927 0.24,0.156 10 false *2 2.26,1.521 2.677,1.677 0.417,0.156 10 false *1: LH 2.26,1.865 2.708,2.01 0.448,0.146 10 false *2: RH 0.302,3.729 0.594,3.885 0.292,0.156 10 false H39 0.552,4.26 0.75,4.427 0.198,0.167 10 false LL 2.698,4.229 2.927,4.375 0.229,0.146 10 false LR 1,2.021 1.313,2.167 0.313,0.146 10 false TRN 2.094,2.042 2.24,2.208 0.146,0.167 10 false E

a.

for LH:

i.

Disconnect the O23 rear combination light assembly LH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O23-1 (TRN) - H39-2 (LL) Always Below 1 Ω
O23-2 (E) - Body ground Always Below 1 Ω
O23-1 (TRN) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the rear combination light assembly LH connector.



b.

for RH:

i.

Disconnect the O22 rear combination light assembly RH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O22-1 (TRN) - H39-8 (LR) Always Below 1 Ω
O22-2 (E) - Body ground Always Below 1 Ω
O22-1 (TRN) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the rear combination light assembly RH connector.




OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
E161601E01
0.023,0.079 2.782,0.428 2.759,0.349 10 Component without wire harness connected: (Outer Rear View mirror Assembly) 1.745,2.71 1.867,2.864 0.122,0.154 10 B 2.158,2.71 2.296,2.880 0.138,0.170 10 E 1.906,2.01 1.805,2.696 false 2.077,2.013 2.204,2.686 false

a.

Remove the outer rear view mirror assembly (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL).


b.

Apply battery voltage to the terminals and check that the side turn signal light turn on.

OK:
Tester Connection Specified Condition
Positive battery (+) → 4 (B)
Negative battery (-) → 3 (E)
Side turn signal light turn on.



c.

Reinstall the outer rear view mirror assembly.



OK

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER, BODY GROUND)

NG

10.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY
9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER, BODY GROUND)
U154014E01
0.04,2.128 2.604,2.485 2.564,0.357 10 Front view of wire harness connector: (to Turn Signal Flasher Assembly) 0.291,3.406 0.586,3.557 0.296,0.151 10 H39 0.04,0.046 2.604,0.403 2.564,0.357 10 Front view of wire harness connector: (to Outer Rear View Mirror Assembly) 0.226,1.54 0.451,1.691 0.225,0.151 10 L6 0.606,1.545 0.759,1.705 0.153,0.160 10 *2 0.191,1.09 0.417,1.241 0.225,0.151 10 M5 1.231,3.457 1.101,4.191 false 0.992,4.191 1.352,4.347 0.360,0.156 10 LL 0.367,1.903 0.509,2.066 0.142,0.163 10 E 2.644,1.846 2.963,2.009 0.319,0.163 10 B 1.408,1.635 0.548,1.973 false 1.618,1.641 2.601,1.929 false 0.606,1.095 0.759,1.255 0.153,0.160 10 *1 2.231,3.466 2.265,4.205 false 2.155,4.205 2.515,4.361 0.360,0.156 10 LR 2.829,1.231 3.268,1.378 0.439,0.147 10 *1: LH 2.829,1.577 3.268,1.724 0.439,0.147 10 *2: RH

a.

for LH:

i.

Disconnect the M5 outer rear view mirror assembly LH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-4 (B) - H39-2 (LL) Always Below 1 Ω
M5-3 (E) - Body ground Always Below 1 Ω
M5-4 (B) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the outer rear view mirror assembly LH connector.



b.

for RH:

i.

Disconnect the L6 outer rear view mirror assembly RH connector.


ii.

Disconnect the H39 turn signal flasher assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-4 (B) - H39-8 (LR) Always Below 1 Ω
L6-3 (E) - Body ground Always Below 1 Ω
L6-4 (B) - Body ground Always 10 kΩ or higher



iv.

Reconnect the turn signal flasher assembly connector.


v.

Reconnect the outer rear view mirror assembly RH connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY
a.

Temporarily replace the outer rear view mirror sub assembly with a new or normally functioning one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Check that the side turn signal light turn on.

OK:

Side turn signal light turn on.




OK

END

NG

REPAIR OR REPLACE OUTER REAR VIEW MIRROR ASSEMBLY