Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM27L0U _59 Vehicle Exterior _049352 LIGHTING (EXT) _0235988 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Circuit  


DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM

E161599E01
1.369,0.575 2.170,0.749 0.801,0.174 10 from Battery 3.407,0.576 3.636,0.723 0.229,0.146 10 DA 3.456,0.389 3.561,0.556 0.106,0.167 10 1 6.642,2 6.863,2.177 0.221,0.177 10 DC 4.952,2.012 5.058,2.165 0.106,0.153 10 8 5.118,2.012 5.366,2.165 0.249,0.153 10 DB 6.382,2.014 6.569,2.167 0.187,0.153 10 22 3.789,2.211 4.815,2.371 1.026,0.160 10 Main Body ECU 4.587,1.31 4.917,1.478 0.331,0.167 10 TAIL 5.311,1.48 5.642,1.648 0.331,0.167 10 TAIL 5.94,0.562 6.341,0.727 0.400,0.165 10 TRLY 0.225,2.813 0.337,2.973 0.112,0.160 10 1 0.225,3.913 0.329,4.059 0.105,0.146 10 2 0.405,3.037 0.523,3.213 0.118,0.175 10 B 0.405,3.676 0.561,3.832 0.156,0.156 10 E 1.854,2.813 1.967,2.973 0.112,0.160 10 2 1.854,3.913 1.959,4.059 0.105,0.146 10 1 5.105,2.813 5.217,2.973 0.112,0.160 10 2 5.105,3.913 5.210,4.059 0.105,0.146 10 1 3.489,2.813 3.601,2.973 0.112,0.160 10 1 3.489,3.913 3.594,4.059 0.105,0.146 10 2 3.67,3.037 3.787,3.213 0.118,0.175 10 B 3.67,3.676 3.826,3.832 0.156,0.156 10 E 0.701,2.967 0.991,3.121 0.290,0.153 10 A15 0.701,3.124 1.591,3.448 0.889,0.324 10 Front Parking Light LH 3.933,2.967 4.223,3.121 0.290,0.153 10 A16 3.933,3.124 4.823,3.448 0.889,0.324 10 Front Parking Light RH 2.297,2.967 2.586,3.121 0.290,0.153 10 A39 2.297,3.124 3.105,3.448 0.808,0.324 10 Side Marker Light LH 5.549,2.967 5.839,3.121 0.290,0.153 10 A38 5.549,3.124 6.357,3.448 0.808,0.324 10 Side Marker Light RH 1.67,5.982 1.783,6.143 0.112,0.160 10 1 1.67,4.873 1.775,5.019 0.105,0.146 10 2 1.851,5.108 1.969,5.284 0.118,0.175 10 B 1.851,5.747 2.007,5.903 0.156,0.156 10 E 2.136,5.057 2.350,5.218 0.215,0.160 10 V9 2.136,5.223 2.988,5.536 0.852,0.314 10 License Plate Light 3.475,5.982 3.588,6.143 0.112,0.160 10 3 3.475,4.873 3.580,5.019 0.105,0.146 10 1 3.656,5.108 3.774,5.284 0.118,0.175 10 B 3.656,5.747 3.812,5.903 0.156,0.156 10 E 3.941,5.057 4.155,5.218 0.215,0.160 10 V8 3.927,5.223 4.810,5.703 0.883,0.480 10 Rear Light LH 5.112,5.982 5.224,6.143 0.112,0.160 10 3 5.112,4.873 5.217,5.019 0.105,0.146 10 1 5.293,5.108 5.410,5.284 0.118,0.175 10 B 5.293,5.747 5.448,5.903 0.156,0.156 10 E 5.577,5.057 5.792,5.218 0.215,0.160 10 V7 5.563,5.223 6.712,5.574 1.149,0.351 10 Rear Light RH 2.444,8.008 2.556,8.168 0.112,0.160 10 1 2.444,6.898 2.549,7.044 0.105,0.146 10 2 2.629,7.134 2.847,7.309 0.218,0.175 10 TL 2.625,7.772 2.781,7.928 0.156,0.156 10 E 2.909,7.083 3.301,7.243 0.392,0.160 10 O21 2.895,7.248 3.723,7.793 0.828,0.545 10 Rear Combination Light LH 4.08,8.008 4.193,8.168 0.112,0.160 10 1 4.08,6.898 4.185,7.044 0.105,0.146 10 2 4.266,7.134 4.484,7.309 0.218,0.175 10 TL 4.261,7.772 4.417,7.928 0.156,0.156 10 E 4.546,7.083 4.944,7.243 0.399,0.160 10 O20 4.532,7.248 5.728,7.602 1.196,0.354 10 Rear Combination Light RH

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TAILLIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test / Tail Light


e.

Check that the taillights turn on/off.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight ON or OFF -

OK:

Taillights turn on/off.



Result
Result Proceed to
OK A
NG (All taillights do not turn on) B
NG (Front parking lights and side marker light do not turn on) C
NG (Taillight and license plate light do not turn on) D


A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FUSE (TAIL)

C

4.CHECK VEHICLE CONDITION

D

10.CHECK VEHICLE CONDITION
2.INSPECT FUSE (TAIL)
a.
E345014E01
1.542,1.656 1.625,1.146 true 0.135,0.073 2.281,0.271 2.146,0.198 12 false Main Body ECU: 1.385,1.688 2,1.885 0.615,0.198 10 false TAIL

Remove the TAIL fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
TAIL fuse Always Below 1 Ω



c.

Reinstall the TAIL fuse.



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
U152779E03
0.156,0.031 2.542,0.385 2.385,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 0.75,2.219 0.958,2.385 0.208,0.167 10 false DA

a.

Disconnect the DA main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA-1 - Body ground Always 11 to 14 V



c.

Reconnect the main body ECU connector.



OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK VEHICLE CONDITION
a.

Check vehicle condition.

Result
Result Proceed to
Front parking light and side marker light do not turn on A
Front parking light does not turn on B
Side marker light does not turn on C



A

5.INSPECT MAIN BODY ECU

B

6.INSPECT FRONT PARKING LIGHT BULB

C

8.INSPECT SIDE MARKER LIGHT BULB
5.INSPECT MAIN BODY ECU
a.
U154104E01
0.089,0.015 2.417,0.367 2.328,0.352 10 Component with harness connected: (Main body ECU (Side View)) 1.777,1.601 2.014,1.745 0.237,0.144 10 DB 0.594,2.83 0.951,2.983 0.357,0.152 10 DB-8 2.046,2.117 1.027,2.899 false

Remove the main body ECU with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DB-8 - Body Ground Light control switch
OFF → TAIL
Below 1 V → 11 to 14 V



c.

Reinstall the main body ECU.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - PARKING LIGHT, SIDE MARKER LIGHT)

NG

REPLACE MAIN BODY ECU

6.INSPECT FRONT PARKING LIGHT BULB
a.

Temporarily replace the front parking light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the front parking light turn on.

OK:

Front parking light turn on.




OK

END

NG

7.CHECK HARNESS AND CONNECTOR (FRONT PARKING LIGHT - BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (FRONT PARKING LIGHT - BODY GROUND)
U154075E01
0.083,0 2.430,0.341 2.347,0.341 10 Front view of wire harness connector: (to Front Parking Light) 0.341,1.175 0.630,1.335 0.290,0.160 10 A15 0.809,1.184 0.965,1.329 0.156,0.145 10 *1 0.341,1.556 0.630,1.716 0.290,0.160 10 A16 0.809,1.566 0.965,1.710 0.156,0.145 10 *2 2.798,1.383 3.227,1.549 0.428,0.166 10 *1: LH 2.798,1.732 3.234,1.887 0.436,0.155 10 *2: RH 1.416,1.871 1.536,2.032 0.120,0.161 10 E 1.757,1.555 1.479,1.861 false

a.

for LH

i.

Disconnect the A15 front parking light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-2 (E) - Body Ground Always Below 1 Ω



iii.

Reconnect the front parking light connector.



b.

for RH

i.

Disconnect the A16 front parking light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-2 (E) - Body Ground Always Below 1 Ω



iii.

Reconnect the front parking light connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - PARKING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SIDE MARKER LIGHT BULB
a.

Temporarily replace the side marker light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the side marker light turn on.

OK:

Side marker light turn on.




OK

END

NG

9.CHECK HARNESS AND CONNECTOR (SIDE MARKER LIGHT - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (SIDE MARKER LIGHT - BODY GROUND)
U154076E01
0.083,0.014 2.488,0.359 2.405,0.345 10 Front view of wire harness connector: (to Side Marker Light) 0.303,1.23 0.575,1.384 0.271,0.154 10 A39 0.756,1.252 0.912,1.401 0.156,0.149 10 *1 0.303,1.67 0.575,1.824 0.271,0.154 10 A38 0.756,1.692 0.912,1.841 0.156,0.149 10 *2 2.685,1.424 3.144,1.575 0.459,0.152 10 *1: LH 2.685,1.778 3.144,1.930 0.459,0.152 10 *2: RH

a.

for LH

i.

Disconnect the A39 side marker light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 - Body Ground Always Below 1 Ω



iii.

Reconnect the side marker light connector.



b.

for RH

i.

Disconnect the A38 front parking light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-1 - Body Ground Always Below 1 Ω



iii.

Reconnect the front turn signal light connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - SIDE MARKER LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE CONDITION
a.

Check vehicle condition.

Result
Result Proceed to
Taillight and license plate light does not turn on A
Taillight (for Rear combination light) does not turn on B
Taillight (for Rear light) does not turn on C
License plate light does not turn on D



A

11.INSPECT MAIN BODY ECU

B

12.INSPECT REAR COMBINATION LIGHT BULB (TAILLIGHT BULB)

C

14.INSPECT REAR LIGHT (TAILLIGHT BULB)

D

16.INSPECT LICENSE PLATE LIGHT BULB
11.INSPECT MAIN BODY ECU
a.
U154103E02
1.51,3.031 0.677,3.667 true 0.094,0 2.438,0.354 2.344,0.354 10 false Component with harness connected: (Main Body ECU (Side View)) 1.531,2.313 1.771,2.458 0.24,0.146 10 false DC 0.417,3.677 0.875,3.844 0.458,0.167 10 false DC-22

Remove the main body ECU with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DC-22 - Body Ground Light control switch
OFF → TAIL
Below 1 V → 11 to 14 V



c.

Reinstall the main body ECU.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - TAILLIGHTS, LICENSE PLATE LIGHT)

NG

REPLACE MAIN BODY ECU

12.INSPECT REAR COMBINATION LIGHT BULB (TAILLIGHT BULB)
a.

Temporarily replace the rear combination light (taillight) bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the rear combination light (taillight) turn on.

OK:

Rear combination light (taillight) turn on.




OK

END

NG

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT (TAILLIGHT) - BODY GROUND)
13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT (TAILLIGHT) - BODY GROUND)
U154077E01
0.128,0.047 2.491,0.412 2.362,0.365 10 Front view of wire harness connector: (to Rear Combination Light) 0.359,1.322 0.668,1.483 0.310,0.161 10 O21 0.836,1.34 0.999,1.494 0.163,0.154 10 *1 0.359,1.722 0.668,1.883 0.310,0.161 10 O20 0.836,1.74 0.999,1.894 0.163,0.154 10 *2 2.385,1.462 2.800,1.623 0.415,0.161 10 *1: LH 2.385,1.83 2.832,1.991 0.447,0.161 10 *2: RH 1.283,1.966 1.435,2.104 0.152,0.138 10 E 1.513,1.697 1.358,1.95 false

a.

for LH:

i.

Disconnect the O21 rear combination light LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O21-1 (E) - Body ground Always Below 1 Ω



iii.

Reconnect the rear combination light LH connector.



b.

for RH:

i.

Disconnect the O20 rear combination light RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O20-1 (E) - Body ground Always Below 1 Ω



iii.

Reconnect the rear combination light RH connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - REAR COMBINATION LIGHT (TAILLIGHT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT REAR LIGHT (TAILLIGHT BULB)
a.

Temporarily replace the rear light (taillight) bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>REAR LIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the rear light (taillight) turn on.

OK:

Rear light (taillight) turn on.




OK

END

NG

15.CHECK HARNESS AND CONNECTOR (REAR LIGHT (TAILLIGHT) - BODY GROUND)
15.CHECK HARNESS AND CONNECTOR (REAR LIGHT (TAILLIGHT) - BODY GROUND)
U154078E01
0.149,0.044 2.523,0.391 2.374,0.347 10 Front view of wire harness connector: (to Rear Light) 0.269,1.186 0.481,1.349 0.211,0.163 10 V8 0.658,1.192 0.811,1.354 0.153,0.162 10 *1 0.269,1.623 0.481,1.786 0.211,0.163 10 V7 0.658,1.628 0.811,1.790 0.153,0.162 10 *2 2.429,1.426 2.843,1.588 0.414,0.162 10 *1: LH 2.429,1.763 2.877,1.925 0.447,0.162 10 *2: RH 1.091,1.953 1.220,2.109 0.128,0.155 10 E 1.618,1.658 1.158,1.953 false

a.

for LH:

i.

Disconnect the V8 rear light LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V8-3 (E) - Body ground Always Below 1 Ω



iii.

Reconnect the rear light LH connector.



b.

for RH:

i.

Disconnect the V7 rear light RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-3 (E) - Body ground Always Below 1 Ω



iii.

Reconnect the rear light RH connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - REAR LIGHT (TAILLIGHT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT LICENSE PLATE LIGHT BULB
a.

Temporarily replace the license plate light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>LICENSE PLATE LIGHT ASSEMBLY>REMOVAL).


b.

Check that the license plate light turns on.

OK:

License plate light turns on.




OK

END

NG

17.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - BODY GROUND)
17.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - BODY GROUND)
U154079E01
0.085,0.051 2.453,0.414 2.368,0.363 10 Front view of wire harness connector: (to License Plate Light) 0.327,1.352 0.534,1.501 0.207,0.149 10 V9 2.264,1.899 2.391,2.054 0.128,0.155 10 E 1.825,1.543 2.33,1.877 false

a.

Disconnect the V9 license plate light LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-1 (E) - Body ground Always Below 1 Ω



c.

Reconnect the license plate light connector.

i.

Reconnect the license plate light connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - LICENSE PLATE LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR