Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER
RM27L0U _59 Vehicle Exterior _049355 EXTERIOR PANELS / TRIM _0236010 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52174E 1.INSTALL REAR BUMPER BAR BRACKET LH

B191669

a.

Install the rear bumper bar bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52173E 2.INSTALL REAR BUMPER BAR BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 58356D 3.INSTALL REAR BUMPER ARM BRACKET LH

B191668

a.

Install the rear bumper arm bracket the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 58355C 4.INSTALL REAR BUMPER ARM BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 58352D 5.INSTALL REAR FLOOR STAY BRACKET LH

B191667

a.

Install the rear floor stay with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 58352A 6.INSTALL REAR FLOOR STAY BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 52615 7.INSTALL REAR BUMPER ENERGY ABSORBER

B191666

a.

Install the rear bumper energy absorber.


Hide 52588 8.INSTALL REAR BUMPER END RETAINER LH

B191665

a.

Engage the 2 claws and rear bumper end retainer.


b.

Tighten the screw.


Hide 52587 9.INSTALL REAR BUMPER END RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52563A 10.INSTALL REAR BUMPER UPPER RETAINER LH

B191664

a.

Engage the 4 claws and install the rear bumper upper retainer.


b.

Tighten the 3 screws.


Hide 52562B 11.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 89341B 12.INSTALL NO. 2 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

Hide 82165 13.INSTALL NO. 2 FRAME WIRE (w/ Intuitive Parking Assist System)

B191663

a.

Connect the 6 harness clamps and No. 2 frame wire.


b.

Connect the 4 connectors.


Hide 14.INSTALL GROMMET

B191661E02
2.323,0.042 3.01,0.198 0.688,0.156 10 false RH Side: 0.365,0.042 1.052,0.198 0.688,0.156 10 false LH Side:

a.

Install the 6 grommets.


Hide 52169C 15.INSTALL REAR BUMPER LOWER COVER (w/o Towing Hitch)

B191662E01
0.177,1.289 1.440,1.501 1.262,0.212 10 Double-sided Tape 1.527,0.298 0.957,1.228 false

a.

Apply Primer G to the installation part of the rear bumper lower cover.

HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



b.

Install the new rear bumper lower cover onto the rear bumper cover, as shown in the illustration.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




Hide 52169C 16.INSTALL REAR BUMPER LOWER COVER (w/ Towing Hitch)

B191658E01
0.169,1.295 1.395,1.485 1.225,0.191 10 Double-sided Tape 2.653,0.38 0.921,1.247 false 1.489,0.294 0.921,1.247 false

a.

Apply Primer G to the installation part of the rear bumper lower cover.

HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



b.

Install the new rear bumper lower cover onto the rear bumper cover, as shown in the illustration.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




Hide 81920 17.INSTALL REFLEX REFLECTOR ASSEMBLY LH

B191657

a.

Install the reflex reflector with the nut.


Hide 81910 18.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.