Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.10
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P014C  A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D  A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P014E  A/F Sensor Slow Response - Rich to Lean Bank 2 Sensor 1  P014F  A/F Sensor Slow Response - Lean to Rich Bank 2 Sensor 1  P015A  A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B  A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  P015C  A/F Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1  P015D  A/F Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1  


DESCRIPTION

HINT:
·

Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.



DTC No. DTC Detection Condition Trouble Area
P014C
P014E
The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


P014D
P014F
The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
P015A
P015C
The "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
P015B
P015D
The "Lean to Rich delay level*" value is standard or more (2 trip detection logic).

*: Calculated by ECM based on the air fuel ratio sensor output.


MONITOR DESCRIPTION

After the engine is warmed up, the ECM carries out air-fuel ratio feedback control, and maintains the air-fuel ratio at the theoretical level. In addition, after all the preconditions have been met, active air-fuel ratio control is carried out for approximately 10 seconds, and during active air-fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing a specific injection volume based on the theoretical air-fuel ratio learned during normal air-fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air-fuel ratio control.

If the air fuel ratio sensor's response ability is reduced, DTCs P014C P014D, P014E and P014F are stored.

If the time it takes the air fuel ratio sensor output to change is delayed, DTCs P015A, P015B, P015C and P015D are stored.

A223538E46
4.208,1.75 4.052,1.448 false 5.229,1.99 5.448,1.427 false 4.188,3 4.073,2.76 false 4.5,3.021 4.75,2.646 false 0.135,0.094 2.865,0.281 2.729,0.188 10 false Air Fuel Ratio (A/F) Sensor Output: 0.292,0.979 1.5,1.167 1.208,0.188 10 false Active A/F Control 0.292,1.938 1.896,2.281 1.604,0.344 10 false A/F Sensor Output (response rate) 3.563,1.354 4.063,1.542 0.5,0.188 10 false Normal 5.469,1.281 6.229,1.469 0.76,0.188 10 false Malfunction 4.438,0.542 5.25,0.729 0.813,0.188 10 false 10 Seconds 0.292,4.25 1.698,4.438 1.406,0.188 10 false Fuel Injection Volume 2.771,3.969 3.417,4.156 0.646,0.188 10 false Increase 2.771,4.438 3.417,4.625 0.646,0.188 10 false Decrease 1.833,0.771 2.229,0.917 0.396,0.146 10 false ON 1.833,1.073 2.208,1.26 0.375,0.188 10 false OFF 0.292,3.125 1.542,3.542 1.25,0.417 10 false A/F Sensor Output (delay time) 3.583,2.688 4.083,2.875 0.5,0.188 10 false Normal 4.792,2.542 5.552,2.729 0.76,0.188 10 false Malfunction

MONITOR STRATEGY

Related DTCs P014C: Air fuel ratio sensor (bank 1) slow response (rich to lean)
P014D: Air fuel ratio sensor (bank 1) slow response (lean to rich)
P014E: Air fuel ratio sensor (bank 2) slow response (rich to lean)
P014F: Air fuel ratio sensor (bank 2) slow response (lean to rich)
P015A: Air fuel ratio sensor (bank 1) delayed response (rich to lean)
P015B: Air fuel ratio sensor (bank 1) delayed response (lean to rich)
P015C: Air fuel ratio sensor (bank 2) delayed response (rich to lean)
P015D: Air fuel ratio sensor (bank 2) delayed response (lean to rich)
Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Vehicle speed sensor, crankshaft position sensor
Frequency of Operation Once per driving cycle
Duration 10 to 15 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P0300 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P0451, P0452, P0453 (EVAP system)
P2440 - P2447 (Secondary air injection system)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC valve)
Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions met -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idle OFF
Engine speed 1000 to 2500 rpm
Air fuel ratio sensor status Activated
Fuel-cut OFF
Engine load 10 to 70%
Shift position 2nd or more
Catalyst monitor Not yet
Mass air flow 4 to 11.4 gm/sec

TYPICAL MALFUNCTION THRESHOLDS

Air Fuel Ratio Sensor (Bank 1) Slow Response (Rich to Lean)
Rich to Lean Response rate deterioration level 0.04 V or less

Air Fuel Ratio Sensor (Bank 1) Slow Response (Lean to Rich)
Lean to Rich Response rate deterioration level -0.045 V or higher

Air Fuel Ratio Sensor (Bank 2) Slow Response (Rich to Lean)
Rich to Lean Response rate deterioration level 0.04 V or less

Air Fuel Ratio Sensor (Bank 2) Slow Response (Lean to Rich)
Lean to Rich Response rate deterioration level -0.045 V or higher

Air Fuel Ratio Sensor (Bank 1) Delayed Response (Rich to Lean)
Rich to Lean delay level 350 ms or more

Air Fuel Ratio Sensor (Bank 1) Delayed Response (Lean to Rich)
Lean to Rich delay level 350 ms or more

Air Fuel Ratio Sensor (Bank 2) Delayed Response (Rich to Lean)
Rich to Lean delay level 350 ms or more

Air Fuel Ratio Sensor (Bank 2) Delayed Response (Lean to Rich)
Lean to Rich delay level 350 ms or more

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation pattern will activate the A/F sensor response monitor.


A201252E02
0.676,0.41 1.594,0.578 0.918,0.168 10 Vehicle Speed 0.181,0.81 1.567,1.402 1.387,0.592 10 Between 75 km/h and 100 km/h (47 mph and 62 mph) 1.223,2.265 1.599,2.425 0.376,0.161 10 Idling 0.353,2.544 1.591,2.697 1.238,0.153 10 Ignition Switch off 2.35,2.148 2.547,2.338 0.197,0.189 10 [A] 3.908,0.765 4.115,0.940 0.207,0.175 10 [B] 2.068,2.879 2.907,3.047 0.838,0.168 10 Warming up 3.574,2.903 4.357,3.050 0.783,0.146 10 10 minutes 5.712,2.75 6.051,2.896 0.339,0.145 10 Time 4.655,3.052 4.852,3.241 0.197,0.189 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details.

8.

Check that the monitor item O2 Sensor is Incomplete.

HINT:

The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1, and LR DELAY B2S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated in each test item).


9.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].

10.

Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Check that the monitor item O2 Sensor becomes Complete.

HINT:

Check the test values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1, and LR DELAY B2S1.


12.

If the monitor item O2 Sensor does not become Complete (if the test values indicated on the Techstream do not change), perform Readiness Monitor Drive Pattern for the A/F sensor and heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>READINESS MONITOR DRIVE PATTERN).

13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

14.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

16.

Input the DTC: P014C, P014D, P014E, P014F, P015A, P015B, P015C and P015D.

17.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



18.

If the DTC judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output A
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D and other are output B

HINT:

If any DTCs other than DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0031).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

4.INSPECT AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR FUEL RATIO SENSOR
a.

Check that the proper air fuel ratio sensor is installed to the vehicle.

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read pending DTCs.

Result
Result Proceed to
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output A
DTC is not output (Pending DTC is not output) B



A

7.REPLACE AIR FUEL RATIO SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read pending DTCs.

Result
Result Proceed to
DTC is not output (Pending DTC is not output) A
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output B



A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO