Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL PUMP › from 2016.10
RM27L0U _51 Engine / Hybrid System _049298 3UR-FE FUEL _0235582 FUEL PUMP A

3UR-FE FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 77100 1.REMOVE FUEL TANK ASSEMBLY

a.

Remove the fuel tank assembly (See Page Engine / Hybrid System>3UR-FE FUEL>FUEL TANK>REMOVAL).


Hide 77020A 2.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A152246C01
0.531,0.646 0.948,0.229 true 1.99,3.031 2.167,2.615 2.167,2.615 2.406,2.615 true 1.938,3.927 2.521,3.927 true 0.76,2.927 0.99,2.927 0.99,2.927 1.24,3.417 true 0.771,2.625 1,2.625 1,2.625 1.438,3.063 true 1.052,4.104 1.052,3.688 1.052,3.688 1.458,3.688 true 1.052,3.833 1.49,3.833 true 2.448,2.49 2.76,2.646 0.313,0.156 10 false *1 0.604,2.521 0.917,2.677 0.313,0.156 10 false *2 0.594,2.833 0.906,2.99 0.313,0.156 10 false *3 2.552,3.823 2.865,3.979 0.313,0.156 10 false *4 0.979,4.167 1.292,4.323 0.313,0.156 10 false *5
*1 Fuel Tank Tube
*2 Tube Joint
*3 Tube Joint Clip
*4 Fuel Suction Plate
*5 O-Ring


Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank tubes.




b.
A390960C01
0.771,1.208 0.771,0.792 true 0.448,1.188 1.281,1.188 1.281,1.188 1.281,0.938 true 0.26,1.073 0.573,1.229 0.313,0.156 10 false *a 0.708,1.323 0.833,1.5 0.125,0.177 10 true . 2.625,0.635 2.75,0.813 0.125,0.177 10 true .
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the fuel suction with pump and gauge tube assembly and fuel tank assembly.

NOTICE:
·

The fuel tank assembly cutout is attached to the protrusion on the fuel tank vent tube assembly.

·

If the fuel suction with pump and gauge tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel suction with pump and gauge tube assembly will co-rotate and result in the fuel suction with pump and gauge tube assembly being damaged.

·

Make sure to apply a co-rotation prevention check mark to prevent the fuel suction with pump and gauge tube assembly from co-rotating.




c.
A390961C01
1.229,2.885 1.427,2.885 1.427,2.885 1.625,2.573 true 0.646,0.302 0.833,0.302 0.833,0.302 0.896,0.51 true 1.313,0.771 1.479,0.646 1.479,0.646 1.635,0.646 true 1.979,2.365 2.135,2.094 2.135,2.094 2.292,2.094 true 1,1.99 1.188,1.99 1.188,1.99 1.656,2.49 true 1.063,4.604 1.26,4.604 1.26,4.604 1.646,4.26 true 2.344,1.979 2.656,2.135 0.313,0.156 10 false *1 0.479,0.177 0.792,0.333 0.313,0.156 10 false *a 1.052,2.792 1.365,2.948 0.313,0.156 10 false *b 0.833,1.875 1.146,2.031 0.313,0.156 10 false *c 0.875,4.49 1.188,4.646 0.313,0.156 10 false *d 1.688,0.542 2,0.698 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




d.
A390962C01
0.677,2.031 0.906,2.031 0.906,2.031 1.094,1.823 true 2.104,1.313 2.25,1.094 2.25,1.094 2.438,1.094 true 0.708,0.74 0.938,0.74 0.938,0.74 1.354,1.021 true 2.49,0.979 2.802,1.135 0.313,0.156 10 false *1 0.531,0.635 0.844,0.792 0.313,0.156 10 false *a 0.5,1.938 0.813,2.094 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


e.
A390959C01
0.76,0.125 0.958,0.125 0.958,0.125 1.24,0.281 true 2.802,1.583 2.802,1.406 2.802,1.406 2.646,1.198 true 0.563,0.031 0.875,0.188 0.313,0.156 10 false *a 2.74,1.594 3.052,1.75 0.313,0.156 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).


f.
A387317C02
0.615,1.198 0.854,1.198 0.854,1.198 1.333,0.906 true 1.74,1.083 2.573,1.083 true 2.604,1 2.917,1.198 0.313,0.198 10 true *a 0.427,1.094 0.74,1.25 0.313,0.156 10 false *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


g.
A391923C01
0.917,0.677 1.115,0.677 1.115,0.677 1.313,0.99 false 0.656,2.542 1.052,2.542 false 1.927,0.802 2.208,0.583 2.208,0.583 2.427,0.583 false 1.781,1.146 1.99,1.594 1.99,1.594 2.25,1.594 true 0.771,2.125 0.969,2.125 0.969,2.125 1.375,2.385 false 0.75,0.583 1.063,0.74 0.313,0.156 10 false *1 0.479,2.448 0.813,2.604 0.333,0.156 10 false *a 2.458,0.479 2.771,0.635 0.313,0.156 10 false *b 0.583,2.021 0.896,2.177 0.313,0.156 10 false *c 2.281,1.5 2.594,1.656 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V100135

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


h.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


i.
A387343C01
3.177,1.125 3.073,0.906 true 0.625,1.521 0.99,1.521 true 1.281,0.604 1.5,0.365 1.5,0.365 1.708,0.365 true 0.458,1.417 0.771,1.573 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b 3.156,1.135 3.406,1.354 0.25,0.219 10 false *c
*a SST (Plate)
*b SST (Handle)
*c SST (Claw Set)
V100135

Loosen


Slowly loosen the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.




j.

While one person slowly loosens the fuel pump gauge retainer, have another person press down the rising fuel suction with pump and gauge tube assembly, securely attach the protrusion of the fuel suction with pump and gauge tube assembly to the groove of the fuel tank assembly, and then remove the fuel pump gauge retainer while making sure that the fuel suction with pump and gauge tube assembly is properly aligned.

A390966C01
0.281,1.885 0.479,1.885 0.479,1.885 0.854,1.219 true 2.594,2.177 2.594,1.76 2.594,1.76 2.885,1.76 true 2.594,1.865 3.25,1.865 true 1.125,0.573 1.281,0.146 1.281,0.146 1.031,0.146 true 0.115,1.771 0.427,1.927 0.313,0.156 10 false *a 0.844,0.052 1.156,0.208 0.313,0.156 10 false *b 1.021,1.844 1.333,2 0.313,0.156 10 false *c 1.948,0.302 2.26,0.458 0.313,0.156 10 false *d 2.521,2.198 2.833,2.354 0.313,0.156 10 false *e 5.625,1.74 5.938,1.896 0.313,0.156 10 false *c 6.563,0.156 6.875,0.313 0.313,0.156 10 false *d
*a SST (Plate) *b SST (Handle)
*c Person in Charge of Loosening *d Person in Charge of Supporting
*e Co-rotation Prevention Check Mark - -


NOTICE:
·

The fuel suction with pump and gauge tube assembly is equipped with a spring that pushes against the bottom of the fuel tank assembly to constantly lift the fuel suction with pump and gauge tube assembly upwards.

·

If the fuel suction with pump and gauge tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel suction with pump and gauge tube assembly will co-rotate and result in the fuel suction with pump and gauge tube assembly and fuel tank assembly being damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.

·

Do not bend the arm of the fuel sender gauge assembly.




k.

Remove the gasket from the fuel tank assembly.