Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P011B    Engine Coolant Temperature / Intake Air Temperature Correlation

for Preparation Click here


DESCRIPTION

The ECM calculates the difference between the readings of the coolant temperature sensor and intake air temperature sensor. If the difference is greater than 20°C (68°F), the ECM will judge this as a malfunction and will set this DTC.

DTC No.
DTC Detection Condition
Trouble Area
P011B
When conditions (a), (b), (c), (d) and (e) are met (2 trip detection)
(a) Battery voltage is 10.5 V or more
(b) 37.5 seconds after the engine has been started after the ignition switch has been OFF for more than 7 hours
(c) The minimum intake air temperature after the engine has been started is more than -10°C (14°F)
(d) The average coolant temperature before the engine is started is more than -10°C (14°F)
(e) The difference between the readings of the ECT and IAT is greater than 20°C (68°F)
  1. IAT sensor
  2. ECT sensor
  3. ECM

A163149E36

HINT:
  1. Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
  2. For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the ECT and IAT are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, this does not necessarily indicate a fault.


MONITOR DESCRIPTION

The ECM monitors the difference between the Engine Coolant Temperature (ECT) and the Intake Air Temperature (IAT) when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine started cold after 7 hours or more has elapsed since the engine was stopped (ignition switch turned to OFF) on the previous trip. If the difference between the ECT and the IAT on a cold start exceeds 20°C (68°F), the ECM interprets this as a malfunction in the ECT sensor circuit and IAT sensor circuit, and sets the DTC.

MONITOR STRATEGY


Related DTCs
P011B: ECT / IAT sensor correlation
Required Sensors / Components (Main)
ECT / IAT sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
37.5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
All of following conditions is met
Condition 1 and 2
1. All of the following conditions are met
Condition (a), (b), (c) and (d)
(a) After ignition switch ON and engine not running time
Less than 20 seconds
(b) Soak Time
7 hours or more
(c) Battery voltage
10.5 V or more
(d) Time after engine start
21 seconds or more
2. Either of the following conditions is met
Condition (a) and (b)
(a) After engine start minimum IAT
-10°C (14°F) or more
(b) Before engine start ECT
-10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Deviated ECT minus Deviated IAT
Less than -20°C (-4°F) or more than 20°C (68°F)

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION P011B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P011B
    A
    P011B and other DTCs
    B

    HINT:
    If any DTCs other than P011B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Leave the vehicle for 7 hours or more.

    HINT:
    It is necessary leave the vehicle for 7 hours or more to allow conditions similar to the DTC detection conditions.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

  1. Read the value displayed on the tester.

    OK:
    The intake air temperature and the outside air temperature are within 10°C (50°F) of each other.

    HINT:
    Temperature readings on the vehicle's outside temperature gauge (if equipped) are not suitable for comparing to the IAT reading. The outside temperature gauge has a significant delay built in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    OK:
    The coolant temperature and the outside air temperature are within 10°C (50°F) of each other.

    HINT:
    If the result is not as specified, check that there are heat sources such as a block heater in the engine compartment.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE ECM (Click here)