Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to the ON position. The MIL goes off when the engine is started.


A116143E36


WIRING DIAGRAM


A163161E02


A136097E10


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.

    OK:
    MIL lights up.



OK
GO TO MIL CIRCUIT (Click here)
NG


2.CHECK CONNECTION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Check the communication between the tester and ECM.

    Result:

    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK THROTTLE BODY (CHECK MIL ILLUMINATED)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY (Click here)
B


4.CHECK ACCELERATOR PEDAL ROD (CHECK MIL ILLUMINATED)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ROD (Click here)
B


5.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the VVT sensor for intake camshaft bank 1 connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor for intake camshaft bank 1 connector.



A
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (Click here)
B


6.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the VVT sensor for exhaust camshaft bank 1 connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor for exhaust camshaft bank 1 connector.



A
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (Click here)
B


7.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the VVT sensor for intake camshaft bank 2 connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor for intake camshaft bank 2 connector.



A
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (Click here)
B


8.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the VVT sensor for exhaust camshaft bank 2 connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor for exhaust camshaft bank 2 connector.



A
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (Click here)
B


9.CHECK CHARCOAL CANISTER ASSEMBLY (CHECK MIL ILLUMINATED)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the canister pump module connector.



A
REPLACE CHARCOAL CANISTER ASSEMBLY (Click here)
B


10.CHECK HARNESS AND CONNECTOR


    A162963E01
  1. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the VVT sensor for intake camshaft bank 1 connector.

  1. Disconnect the VVT sensor for exhaust camshaft bank 1 connector.

  1. Disconnect the VVT sensor for intake camshaft bank 2 connector.

  1. Disconnect the VVT sensor for exhaust camshaft bank 2 connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the E9 and E4 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VC (E9-23) - Body ground
    10 kΩ or higher
    VCPA (E4-26) - Body ground
    10 kΩ or higher
    VCP2 (E4-27) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the canister pump module connector.

  1. Reconnect the VVT sensor for exhaust camshaft bank 2 connector.

  1. Reconnect the VVT sensor for intake camshaft bank 2 connector.

  1. Reconnect the VVT sensor for exhaust camshaft bank 1 connector.

  1. Reconnect the VVT sensor for intake camshaft bank 1 connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the throttle body connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)