Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC    P0021    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0022    Camshaft Position "A" - Timing Over-Retarded (Bank 2)

for Preparation Click here

HINT:
If DTC P0011, P0012, P0021 or P0022 is present, check the VVT (Variable Valve Timing) system.


DESCRIPTION

Refer to DTC P0010 .

DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
  1. Valve timing
  2. OCV for intake camshaft
  3. OCV filter
  4. Intake camshaft (bank 1) timing gear assembly
  5. ECM
P0012
P0022
Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
  1. Valve timing
  2. OCV for intake camshaft
  3. OCV filter
  4. Intake camshaft (bank 2) timing gear assembly
  5. ECM

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure applied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timings is large, and changes in actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and sets a DTC.
Example:
  1. A DTC will be set when the following conditions 1) and 2) are met:
  2. 1) It takes 5 seconds or more to change the valve timing by 5° CA.
  3. 2) After above conditions 1) are met, the OCV is forcibly activated during 10 seconds.
    DTCs P0011 and P0021 (Advanced Cam Timing) are detected with 1 trip detection logic.
    DTCs P0012 and P0022 (Retarded Cam Timing) are detected with 2 trip detection logic.
    These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.
  4. The monitor will not run unless the following conditions are met:
    - The engine is warm (the engine coolant temperature is 75°C [167°F] or more).
    - The vehicle has been driven at more than 40 mph (64 km/h) for 3 minutes.
    - The engine has idled for 3 minutes.

MONITOR STRATEGY


Related DTCs
P0011: Advanced intake camshaft timing (bank 1)
P0012: Retarded intake camshaft timing (bank 1)
P0021: Advanced intake camshaft timing (bank 2)
P0022: Retarded intake camshaft timing (bank 2)
Required sensors / components (Main)
VVT OCV, VVT Actuator
Required sensors / components (Related)
Crankshaft position sensor, Camshaft position sensor, ECT sensor
Frequency of operation
Once per driving cycles
Duration
Less than 10 seconds
MIL operation
P0011 and P0021: Immediate
P0012 and P0022: 2 driving cycles
Sequence operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0010, P0020 (OCV bank 1, 2)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0100, P0102, P0103 (MAF meter)
P0115, P0117, P0118 (ECT sensor)
P0125 (Insufficient ECT for closed loop)
P0335 (CKP sensor)
Battery voltage
11 V or more
Engine RPM
500 to 4000 rpm
ECT
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


P0011, P0021: 
Duration of actual valve timing and target valve timing
More than 5° CA (Crankshaft angle)
Valve timing
No change in advanced valve timing

P0012, P0022: 
Duration of actual valve timing and target valve timing
More than 5° CA (Crankshaft angle)
Valve timing
No change in retarded valve timing
If the difference between the target and actual camshaft timings is greater than the specified value, the ECM operates the VVT actuator.
Then, the ECM monitors the camshaft timing change for 5 seconds.

WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE


Abnormal bank
Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022

HINT:
  1. If DTC P0011 or P0012 is displayed, check the bank 1 VVT system circuit.
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0021 or P0022 is displayed, check the bank 2 VVT system circuit.
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0011, P0012, P0021 or P0022
    A
    P0011, P0012, P0021 or P0022 and other DTCs
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

    OK:

    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine idle speed
    OCV ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Select the check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Read the DTCs using the tester.

    OK:
    No DTC outputs.



NG
Go to step 4
OK

SYSTEM IS OK 

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)


    A135015E01
  1. Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft to align the timing marks of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

  1. Turn the crankshaft clockwise by 360° if the timing marks do not align. Check if they align once again.

    OK:
    The timing marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV)
  1. Remove the camshaft timing oil control valve (OCV).



    A095415E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



    A097066E08
  1. Apply the positive battery voltage to terminal 1 and the negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.CHECK OIL PIPE AND OIL CONTROL VALVE FILTER


    G042497E01
  1. Remove the oil pipe No. 1 or oil pipe assembly.

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER AND PIPE
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Select the check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Confirm that no DTC is set using the tester.

    OK:
    No DTC output.

    HINT:
    DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay output even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM IS OK