Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0014    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0015    Camshaft Position "B" - Timing Over-Retarded (Bank 1)

DTC    P0024    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0025    Camshaft Position "B" - Timing Over-Retarded (Bank 2)

for Preparation Click here

HINT:
If DTC P0014, P0015, P0024 or P0025 is present, check the VVT (Variable Valve Timing) system.


DESCRIPTION

Refer to DTC P0013 .

DTC No.
DTC Detection Condition
Trouble Area
P0014
P0024
Valve timing is not adjusted in valve timing advance range
(2 trip detection logic) trip detection logic)
  1. Valve timing
  2. OCV for exhaust camshaft
  3. OCV filter
  4. Exhaust camshaft timing gear assembly
  5. ECM
P0015
P0025
Valve timing is not adjusted in valve timing retard range
(1 trip detection logic)
  1. Valve timing
  2. OCV for exhaust camshaft
  3. OCV filter
  4. Exhaust camshaft timing gear assembly
  5. ECM

MONITOR DESCRIPTION

DTC P0014 and P0024
The ECM compares current valve timing with target valve timing, while the engine is running and after being warmed up, in order to monitor the VVT system on the exhaust side. Valve timing is calculated from the positions of the camshaft and crankshaft. The ECM controls the engine so that current valve timing meets target valve timing. If these timings are not met, the ECM determines this as a malfunction.
DTC P0015 and P0025
The ECM compares current valve timing with target valve timing, while the engine is running and after being warmed up, in order to monitor the VVT system on the exhaust side. Valve timing is calculated from the positions of the camshaft and crankshaft. The ECM controls the engine so that current valve timing meets target valve timing. If these timings are not met, the ECM determines this as a malfunction.

MONITOR STRATEGY


Related DTCs
P0014: Advanced exhaust camshaft timing (bank 1)
P0015: Retarded exhaust camshaft timing (bank 1)
P0024: Advanced exhaust camshaft timing (bank 2)
P0025: Retarded exhaust camshaft timing (bank 2)
Required Sensors / Components (Main)
VVT OCV and VVT Actuator
Required Sensors / Components (Related)
P0014 and P0015:
Exhaust camshaft control actuator bank 1
Exhaust OCV bank 1
P0024 and P0025:
Exhaust camshaft control actuator bank 2
Exhaust OCV bank 2
Frequency of Operation
Continuously
Duration
Less than 10 seconds
MIL Operation
P0014 and P0024: 2 driving cycles
P0015 and P0025: Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0013, P0023 (Exhaust OCV bank 1, 2)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0100, P0102, P0103 (MAF meter)
P0115, P0117, P0118 (ECT sensor)
P0125 (Insufficient ECT for closed loop)
P0335 (CKP sensor)
Battery voltage
11 V or more
Engine RPM
500 to 4000 rpm
Engine coolant temperature
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced camshaft timing: 
Valve timing
No change
Valve timing
Advanced position

Retarded camshaft timing: 
Valve timing
No change
Valve timing
Retarded position
If the difference between the target and actual camshaft timings is greater than the specified value, the ECM operates the VVT actuator.
Then, the ECM monitors the camshaft timing change for 5 seconds.

WIRING DIAGRAM

Refer to DTC P0013 .

INSPECTION PROCEDURE


Abnormal bank
Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1
P0014
P0015
Bank 2
P0024
P0025

HINT:
  1. If DTC P0014 or P0015 is displayed, check the bank 1 VVT system circuit.
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0024 or P0025 is displayed, check the bank 2 VVT system circuit.
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0014, P0015, P0024 or P0025
    A
    P0014, P0015, P0024 or P0025 and other DTCs
    B

    HINT:
    If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

    OK:

    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine idle speed
    OCV ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Select the check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Read the DTCs using the tester.

    OK:
    No DTC output.



NG
Go to step 4
OK

SYSTEM IS OK 

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMP TEETH ON TIMING CHAIN)


    A135015E01
  1. Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft to align the matchmarks of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the matchmarks of the camshaft pulley and camshaft bearing cap align.

  1. Turn the crankshaft clockwise by 360° if the matchmarks do not align. Check if they align once again.

    OK:
    The matchmarks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV)
  1. Remove the OCV.



    A095415E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



    A097066E08
  1. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.CHECK OIL PIPE AND OIL CONTROL VALVE FILTER


    G042497E01
  1. Remove the oil pipe No. 1 or oil pipe assembly.

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER AND PIPE
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Select the check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Confirm that no DTC is set using the tester.

    OK:
    No DTC output.

    HINT:
    DTC P0014, P0015, P0024 or P0025 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM IS OK