Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


MONITOR DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 12.4 mph (20 km/h) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to ECM for 20 seconds (1 trip detection logic):
(a) Vehicle speed more than 12.4 mph (20 km/h)
(b) Engine speed more than 1000 rpm
(c) STA signal ON
  1. Park/Neutral Position (PNP) switch
  2. Starter relay circuit
  3. Ignition switch
  4. ECM

MONITOR STRATEGY


Related DTCs
P0617: Starter signal
Required Sensors / Components (Main)
STARTER relay, PNP switch and Ignition switch
Required Sensors / Components (Related)
Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
Battery voltage
10.5 V or more
Vehicle speed
12.43 mph (20 km/h) or more
Engine speed
1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

WIRING DIAGRAM


A162043E04


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON position and START position.

    OK:

    Ignition Switch Positions
    Starter Signal
    ON
    OFF
    START
    ON



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT PARK/NEUTRAL POSITION SWITCH


    A093221E20
  1. Inspect the Park/Neutral Position (PNP) switch.

    1. Disconnect the P1 PNP switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Shift Position
      Tester Connection
      Specified Condition
      P
      2 - 6, 4 - 5
      Below 1 Ω
      R
      1 - 2
      Below 1 Ω
      N
      2 - 9, 4 - 5
      Below 1 Ω
      D
      2 - 7
      Below 1 Ω
      2
      2 - 3
      Below 1 Ω
      L
      2 - 8
      Below 1 Ω

    3. Reconnect the PNP switch connector.



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


3.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON position and the START position.

    OK:

    Ignition Switch Positions
    STARTER SIG
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG


4.INSPECT IGNITION SWITCH ASSEMBLY


    B050489E19
  1. Disconnect the I15 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Condition
    Terminal No.
    Specified Condition
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    1 - 3
    Below 1 Ω
    ON
    1 - 2, 1 - 3, 2 - 3, 5 - 6
    START
    4 - 5, 4 - 6, 5 - 6, 1 - 2

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (GO TO NEXT STEP 5 AFTER REPLACEMENT) (Click here)
OK


5.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON position and the START position.

    OK:

    Ignition Switch Positions
    STARTER SIG
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)