Home › ENGINE › 2GR-FE LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE OIL COOLER
  1. Clean the oil cooler contact surface on the cooler mounting.



    A136292
  1. Install a new O-ring to the oil cooler.



    A136291
  1. Install the oil cooler assembly with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

    Install the 2 water by-pass hoses with the bolt, 2 clamps, and 4 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A129649E01
  1. Install a new gasket as shown in the illustration.



    A129641E01
  1. Install the exhaust manifold sub-assembly LH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



3. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A140784
  1. Install the No. 2 insulator with the 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



4. INSTALL NO. 2 MANIFOLD STAY


    A140783E01
  1. Install the No. 2 manifold stay with the bolt and nut in the order shown in the illustration.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



5. INSTALL EXHAUST PIPE ASSEMBLY
for 2WD:(Click here)
for 4WD:(Click here)


6. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap.

    Engine oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30

    Capacity: 
    Item
    Standard Condition
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 lmp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 lmp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 lmp. qts)



7. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



8. INSPECT FOR OIL LEAK
  1. Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.



9. CHECK ENGINE OIL LEVEL


10. INSTALL NO. 1 ENGINE UNDER COVER


    A162362
  1. Install the No. 1 engine under cover sub-assembly with the 8 bolts and 4 clips.