Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM3650E _59 Vehicle Exterior _079876 WINDOW / GLASS _0387521 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BACK DOOR SEAL

a.
B594787

Install a new back door seal.

HINT:

Perform the operations on the left and right side.



Hide 62785F 2.INSTALL BACK DOOR GLASS SPACER

a.
B602802

Install all new back door glass spacers centrally on the marks.


Hide 64818B 3.INSTALL NO. 1 WINDSHIELD GLASS SPACER

a.
B536791

Install all new No. 1 windshield glass spacers (1) centrally on the marks.


Hide 68131 4.INSTALL BACK DOOR GLASS

HINT:
·

The vehicle can be towed away or driven without the back door glass.

·

When carrying out removal/installation work and during the hardening time, the vehicle must be standing on its wheels on a level surface.

·

The back door glass are bonded to the body. This bonding will increase the torsional rigidity of the vehicle. To obtain perfect bonding, comply with the installation procedure described in the following.



a.

When reusing the back door glass:

i.
B539819

Position the scraper (2) as shown and remove the residual adhesive bead (1) up to remaining thickness.

Standard Dimension:
Area Dimension
Remaining thickness of adhesive bead 0.5 mm (0.0197 in.)




b.

Clean back door glass and body aperture with residual adhesive bead.

Cleaner:

Cleaner R1, Cleaner R2


HINT:

Protect vehicle interior against contamination.



c.
B539818

Install the 2 protective tapes (1) to the roof.

Standard Dimension:
Area Dimension
A 250 mm (9.84 in.)



d.

Apply glass activator to the back door glass so that a wide line of glass activator is located next to the squeezed adhesive bead.

Glass activator:

Repair Kit, Window Glass, Cold, 1 Hour


NOTICE:
·

The glass activator is used for adhesion between glass or ceramic glass and the adhesive. Therefore, a thin, homogeneous and continuous line of glass activator must be applied. If the back door glass is to be reused with a cut-back adhesive bead, glass activator is not needed.

·

The glass activator may not be applied in the field of view or the point grid. Fresh glass activator in the field of view must immediately be wiped off because hardened glass activator will leave a haze behind.

Cleaner:

Cleaner R2




HINT:
·

Protrusion of glass activator against the compressed adhesive bead: 1.0 to 2.0 mm (0.0394 to 0.0787 in.)

·

Allow the glass activator to dry for 2 minutes.




e.

Provide the glue cartridge.

Adhesive:

Repair Kit, Window Glass, Cold, 1 Hour



f.
B539808

Prepare the glue cartridge with the standard nozzle C.

Standard Nozzle C:

Repair Kit, Window Glass, Cold, 1 Hour


Standard Dimension:
Area Dimension
A 7.0 to 9.0 mm (0.276 to 0.354 in.)
B 11 to 13 mm (0.433 to 0.512 in.)



g.
B536794

Apply bead joint in area (1).


h.

Apply adhesive bead within the mark (2) on the back door glass.

Adhesive bead:
Area Dimension
a 7.0 to 9.0 mm (0.276 to 0.354 in.)
b 11 to 13 mm (0.433 to 0.512 in.)



i.
B536790

Using suction cups, fit back door glass (1) carefully.

HINT:

At the same time, guide the back door glass parallel to the C-pillar, fit at the top and align on the side edges as well as the upper and lower edge.



j.
B536844C01
0,0 0,0 false
(1) Roof outer skin
(2) Rear window


Using the special tools 0 496 076 (00 9 470) and 0 495 259 (51 0 010), measuring gap dimension back door glass to roof outer skin.

SST
09800-WA340  09800-WA350  

Standard Clearance:
Area Dimension
a 5.8 to 9.1 mm (0.228 to 0.358 in.)
b 0.6 to 4.2 mm (0.0236 to 0.165 in.)



k.

Press the back door glass on evenly all the way around and engage at the back door glass spacer.


l.
B536796

Secure back door glass (1) with protective tapes (2) on the roof.


m.
B536788

Tighten down T25 screw (2).

HINT:

Perform the operations on the left and right side.



n.

Connect the connector (1).

HINT:

Perform the operations on the left and right side.



Hide 5.INSTALL NO. 1 AMPLIFIER ANTENNA ASSEMBLY

Hide 81570 6.INSTALL CENTER STOP LIGHT ASSEMBLY

Hide 67751 7.INSTALL BACK DOOR TRIM BOARD

Hide 64330D 8.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY