Home › Engine / Hybrid System › B48 (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080178 B48 ENGINE MECHANICAL _0388844 FRONT CRANKSHAFT OIL SEAL A

B48 ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT CRANKSHAFT OIL SEAL

NOTICE:
·

Front crankshaft oil seal damage.

Touching the sealing lip (inner) and applying oil to the front crankshaft oil seal will lead to its destruction.

-

Do not touch the sealing lip (inner) of the front crankshaft oil seal.

-

Do not apply oil to the front crankshaft oil seal.

-

Install the front crankshaft oil seal dry.




HINT:

The front crankshaft oil seal must be installed dry. Do not use engine oil or lubricant.


a.

Clean the special tool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) and coat it with fresh engine oil.

SST
09200-WA080  


b.
A441289

Secure special tool 0 496 128 (11 8 801) to the crankshaft using special tool 0 496 129 (11 8 802).

SST
09200-WA080  


c.
A441290

Carefully slide the front crankshaft oil seal (1) in a rotational movement onto the special tool 0 496 128 (11 8 801) until the front crankshaft oil seal rests against the cylinder block sub-assembly.

SST
09200-WA080  

i.

The front crankshaft oil seal must not be tilted in the process.



d.
A441374

Mount the special tool (sleeve) 0 496 130 (11 8 803) on special tool 0 496 128 (11 8 801).

SST
09200-WA080  


e.
A441375

Screw on the special tool (nut) 0 496 131 (11 8 804) until the special tool (sleeve) 0 496 130 (11 8 803) lies flush on the cylinder block sub-assembly.

SST
09200-WA080  

i.

This correctly positions the front crankshaft oil seal.



f.

Remove special tools.


Hide 13470 2.INSTALL CRANKSHAFT PULLEY ASSEMBLY

a.
A441786

Coat sealing surface on the crankshaft pulley assembly (1) with clean engine oil.


b.

Position crankshaft pulley assembly (1).


c.

Replace the E12 bolts (arrows).


d.

Tighten the E12 bolts (arrows).

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


e.

Using SST, tighten the bolts an additional 120°.

SST
09900-WA010  

HINT:
C417459C09
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




f.
A441395

Loosen bolt (2).


g.

Slide the counter support with the bolt (2) back until the teeth (3) are no longer engaged in the gearing of the flywheel sub-assembly (4).


h.

Unscrew the bolt (1) and remove the special tool 0 496 595 (11 6 130).

SST
09700-WA040  


Hide 28100 3.INSTALL STARTER ASSEMBLY

Hide 4.INSTALL FAN AND GENERATOR V BELT

Hide 5.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL