DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0011 P0021 | Advanced cam timing: With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) met (1 trip detection logic)
|
|
| P0012 P0022 | Retarded cam timing: With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) met (2 trip detection logic)
|
| Related DTCs | P0011: Advanced camshaft timing (bank 1) P0012: Retard camshaft timing (bank 1) P0021: Advanced camshaft timing (bank 2) P0022: Retard camshaft timing (bank 2) |
| Required Sensors/Components (Main) | VVT OCV and VVT Actuator |
| Required Sensors/Components (Related) | Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 10 seconds |
| MIL Operation | P0011 and P0021: Immediate P0012 and P0022: 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0100 - P0103 (MAF sensor) P0115 - P0118 (ECT sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) P0340 (CMP sensor) P0351 - P0356 (igniter) |
| Battery voltage | 11 V or more |
| Throttle position learning | Completed |
| Engine RPM | 500 to 4,000 rpm |
| Engine coolant temperature | 75 to 100°C (167 to 212°F) |
| OCV activation | 9.5 seconds or more |
| Response of valve timing | 1 sec/°CA or more (valve timing does not change) |
| Abnormal bank | Advanced timing over (Valve timing is out of specified range) | Retarded timing over (Valve timing is out of specified range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0011, P0012, P0021 or P0022 | A |
| P0011, P0012, P0021 or P0022 and other DTCs | B |
|
| ||||
| A | |
| 2.PREFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect an intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Warm up the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1.
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operations | Specified Conditions |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read DTCs using the tester.
|
| ||||
| NG | |
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head cover (Click here or Click here).
Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
Reinstall the cylinder head cover (Click here or Click here).
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) |
![]() |
Remove the OCV.
Measure the resistance between the terminals of the OCV.
Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.
Reinstall the OCV.
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK IF DTC OUTPUT RECURS |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Confirm that no DTC is set using the tester.
|
| ||||
| NG | ||
| ||