Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here

HINT:
This DTC relates to the Accelerator Pedal Position (APP) sensor.


DESCRIPTION

Refer to DTC P2120 (Click here).

DTC No.
DTC Detection Conditions
Trouble Areas
P2121
Difference between VPA and VPA2 less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator position sensor
  2. ECM

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the voltage outputs of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is a malfunctioning. The ECM turns on the MIL and the DTC is set.

MONITOR STRATEGY


Related DTCs
P2121: Accelerator pedal position (APP) sensor rationality
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


Difference between VPA voltage (learned value) and VPA2 voltage (learned value)
Less than 0.4 V, or more than 1.2 V

FAIL-SAFE

The accelerator pedal position sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned OFF, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2)
FI07052E06
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / ACCEL POS #1 and ACCEL POS #2.

  1. Read the values displayed on the tester.

    Standard Voltage:
    Accelerator Pedal
    Operations
    ACCEL POS #1
    (AP#1)
    ACCEL POS #2
    (AP#2)
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V



OK
Go to step 3
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
A116156E01
  1. Disconnect the A19 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VPA (A19-6) - VPA (E8-18)
    Below 1 Ω
    EPA (A19-5) - EPA (E8-20)
    VCPA (A19-4) - VCPA (E8-26)
    VPA2 (A19-3) - VPA2 (E8-19)
    EPA2 (A19-2) - EPA2 (E8-21)
    VCP2 (A19-1) - VCP2 (E8-27)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VPA (A19-6) or VPA (E8-18) - Body ground
    10 kΩ or higher
    EPA (A19-5) or EPA (E8-20) - Body ground
    VCPA (A19-4) or VCPA (E8-26) - Body ground
    VPA2 (A19-3) or VPA2 (E8-19) - Body ground
    EPA2 (A19-2) or EPA2 (E8-21) - Body ground
    VCP2 (A19-1) or VCP2 (E8-27) - Body ground

  1. Reconnect the APP sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed To
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM