Home › BRAKE › BRAKE CONTROL › YAW RATE AND DECELERATION SENSOR (w/ VSC)

YAW RATE AND DECELERATION SENSOR (w/ VSC) > INSTALLATION

for Preparation Click here



1. INSTALL YAW RATE SENSOR


F050581
  1. Install the yaw rate sensor with the 2 bolts.

    Torque:
    12.5 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Make sure that the sensor is at the correct angle when installing.

  1. Connect the yaw rate sensor connector.



2. INSTALL SENSOR BRACKET


F050580
  1. Install the bracket with the bolt.

    Torque:
    12.5 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Install the wire harness clamp.



3. INSTALL COWL SIDE TRIM BOARD (for Regular Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



4. INSTALL COWL SIDE TRIM BOARD (for Access Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



5. INSTALL COWL SIDE TRIM BOARD (for Double Cab)


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



6. INSTALL FRONT DOOR SCUFF PLATE (for Regular Cab)


    B087476E01
  1. Engage the 8 claws and clip, and install the front door scuff plate.



7. INSTALL FRONT DOOR SCUFF PLATE (for Access Cab)


    B087436E01
  1. Engage the 9 claws and clip, and install the front door scuff plate.



8. INSTALL FRONT DOOR SCUFF PLATE (for Double Cab)


    B087411E01
  1. Engage the 9 claws and install the front door scuff plate.



9. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



10. INSTALL FRONT SEAT ASSEMBLY (for Bench Seat Type)


    B121741
  1. Place the front seat in the cabin.

  1. Slide the front seat to the most rearward position.

  1. Tighten the 2 bolts on the front side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Slide the front seat to the most forward position.

  1. Tighten the 2 bolts on the rear side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B121740
  1. Install the 2 wiring harness clamps.

  1. Connect the 3 connectors.



    B121739
  1. Install the belt of the front center seat outer belt into the front center seat outer belt guide.



11. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Bench Seat Type)


    B121738E01
  1. Push in the 2 lock buttons of the 2 front seat headrest supports and install the 2 front seat headrests.



12. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Bench Seat Type)


    B121779E01
  1. Slide the front seat to the most forward position.

  1. Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to place the front seat inner belt over the convex areas of the floor panel.

  1. Install the 2 wiring harness clamps.

  1. Connect the 2 connectors.

  1. Engage the hook.



13. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Bench Seat Type)


    B121780E01
  1. Slide the front seat to the most forward position.

  1. Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to place the front seat inner belt over the convex areas of the floor panel.

  1. Install the 2 wiring harness clamps.

  1. Connect the connector.

  1. Engage the hook.



14. INSTALL FRONT SEAT ASSEMBLY (for Separate Seat Type)


    B087375E01
  1. Place the front seat in the cabin.

  1. Tighten the 2 bolts on the front side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Tighten the 2 bolts on the rear side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B087646E01
  1. Install the wire harness clamp.

  1. Connect the 2 connectors.

  1. w/ Front Seat Side Airbag:

    1. Connect the connector.



15. INSTALL SEAT TRACK COVER (for Separate Seat Type)


B087374E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the seat track cover.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

(Click here)


17. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION
(Click here)


18. CHECK VSC SENSOR SIGNAL
(Click here)