Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
Freeze frame data record the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was LEAN or RICH, and other data, from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.
G038619E02

HINT:
If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.

  1. 3 data sets before the DTC was set
  2. 1 data set when the DTC was set
  3. 1 data set after the DTC was set

LIST OF FREEZE FRAME DATA

LABEL
(Intelligent Tester Display)
Measurement Item/Range
Diagnostic Note
INJECTOR
Injector
-
IGN ADVANCE
Ignition advance
-
CALC LOAD
Calculate load
Calculated load by ECM
VEHICLE LOAD
Vehicle load
-
MAF
Mass air flow volume
If value approximately 0.0 g/sec:
  1. Mass air flow meter power source circuit open or short
  1. VG circuit open or short
If value 160.0 g/sec or more:
  1. E2G circuit open
ENGINE SPD
Engine speed
-
VEHICLE SPD
Vehicle speed
Speed indicated on speedometer
COOLANT TEMP
Engine coolant temperature
If value -40°C, sensor circuit open
If value 140°C, sensor circuit shorted
INTAKE AIR
Intake air temperature
If value -40°C, sensor circuit open
If value 140°C, sensor circuit shorted
AIR-FUEL RATIO
Air-fuel ratio
-
PURGE DENSITY
Learning value of purge density
-
PURGE FLOW
Purge flow
-
EVAP PURGE VSV
EVAP purge VSV duty ratio
-
EVAP VAPOR PRES
EVAP vapor pressure
-
KNOCK CRRT VAL
Correction learning value of knocking
-
KNOCK FB VAL
Feedback value of knocking
-
ACCEL POS #1
Absolute No. 1 Accelerator Pedal Position (APP)
-
ACCEL POS #2
Absolute No. 2 APP
-
THROTTLE POS
Throttle position
Read value with ignition switch ON (Do not start engine)
THROTTLE POS
Throttle sensor position
Read value with ignition switch ON (Do not start engine)
THROTTLE POS #2
Throttle sensor position #2
-
THROTTLE MOT
Throttle motor
-
O2S B1 S2
Heated oxygen sensor output
Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor
AFS B1 S1
A/F sensor output
Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor
TOTAL FT #1
Total fuel trim
-
SHORT FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
LONG FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
FUEL SYS #1
Fuel system status (Bank1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
O2FT B1 S2
Fuel trim at heated oxygen sensor
-
AF FT B1 S1
Fuel trim at A/F sensor
-
CAT TEMP B1 S1
Catalyst temperature
-
CAT TEMP B1 S2
Catalyst temperature
-
INI COOL TEMP
Initial engine coolant temperature
-
INI INTAKE TEMP
Initial intake air temperature
-
INJ VOL
Injection volume
-
AIR PMP PRS
Air pump pressure
(Click here)
AIR PMP PLS PRS
Air pump pulsation pressure
(Click here)
STARTER SIG
Starter signal
-
PS SW
Power steering signal
-
PS SIGNAL
Power steering signal (history)
This signal status usually ON until battery terminals disconnected
CTP SW
Closed throttle position switch
-
A/C SIG
A/C signal
-
ELECT LOAD SIG
Electrical load signal
-
STOP LIGHT SW
Stop light switch
-
BATTERY VOLTAGE
Battery voltage
-
ATM PRESSURE
Atmospheric pressure
-
SECOND AIR VSV
Secondary air injection system status
-
ACT VSV
A/C cut status for Active Test
-
EVAP VSV
EVAP purge VSV
VSV for EVAP controlled by ECM (ground side duty control)
FUEL PUMP / SPD
Fuel pump speed status
-
VVT CTRL B1
VVT control status
-
VACUUM PUMP
Key-off EVAP system pump status
(Click here)
EVAP VENT VAL
Key-off EVAP system vent valve status
-
TC/TE1
TC and TE1 terminal of DLC3
-
AI STATUS
Secondary air injection system operation prohibit
(Click here)
VVTL AIM ANGL #1
VVT aim angle
-
VVT CHNG ANGL #1
VVT change angle
-
VVT OCV DUTY B1
VVT OCV operation duty
-
FC IDL
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 1,500 rpm
FC TAU
FC TAU
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
IGNITION
Ignition
-
CYL #1
Cylinder #1 misfire rate
Displayed in only idling
CYL #2
Cylinder #2 misfire rate
Displayed in only idling
CYL #3
Cylinder #3 misfire rate
Displayed in only idling
CYL #4
Cylinder #4 misfire rate
Displayed in only idling
CYL ALL
All cylinder misfire rate
Displayed in only idling
MISFIRE RPM
Misfire RPM
-
MISFIRE LOAD
Misfire load
-
MISFIRE MARGIN
Misfire monitoring
-
ENG RUN TIME
Accumulated engine running time
-
TIME DTC CLEAR
Cumulative time after DTC cleared
-
DIST DTC CLEAR
Accumulated distance from DTC cleared
-
WU CYC DTC CLEAR
Warm-up cycle after DTC cleared
-
MODEL CODE
Identifying model code
TRN2###
FAN MOTOR
Electric fan motor
-
VAPOR PRESS
Vapor pressure
EVAP system pressure as read by canister pressure sensor
ENG OIL PRES SW
Engine oil pressure switch signal
Always ON while engine running
ENGINE TYPE
Identifying engine type
2TR
CYLINDER NUMBER
Identifying cylinder number
4 or 6
DESTINATION
Identifying destination
A (America)
MODEL YEAR
Identifying model year
200#
SYSTEM
Identifying engine system
GASOLINE (gasoline engine)