DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Heated Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0136 |
|
|
| P0137 |
|
|
| P0138 |
|
|



| Related DTCs | P0136: Heated oxygen sensor output voltage (Output voltage) P0136: Heated oxygen sensor impedance (Low) P0137: Heated oxygen sensor output voltage (Low voltage) P0137: Heated oxygen sensor impedance (High) P0138: Heated oxygen sensor output voltage (High voltage) P0138: Heated oxygen sensor output voltage (Extremely high) |
| Required Sensors/Components (Main) | Heated oxygen sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and throttle position sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection Continuous: Others |
| Duration | 90 seconds: Heated oxygen sensor impedance (High) Within 20 seconds: Active air-fuel ratio control detection 30 seconds: Heated oxygen sensor impedance (Low) 10 seconds: Output voltage (High stuck) |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0031, P0032, P0051, P0052 (A/F sensor heater - Sensor 1) P0037, P0038, P0057, P0058 (O2 sensor heater - Sensor 2) P0100 - P0103 (MAF meter) P0110 - P0113 (IAT sensor) P0115 - P0118 (ECT sensor) P0120 - P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0171, P0172 (Fuel system) P0300 - P0308 (Misfire) P0335 (CKP sensor) P0340, P0341 (CMP sensor) P0442 - P0456 (EVAP system) P0500 (VSS) P2196, P2198 (A/F sensor - rationality) P2440 (A/R control valve stuck open) P2441 (A/R control valve stuck close) P2444 (AIP stuck ON) P2445 (AIP stuck OFF) P2A00, P2A03 (A/F sensor - slow response) |
| Active air-fuel ratio control | Executing |
| Active air-fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 70°C (158°F) or more |
| Idling | OFF |
| Engine RPM | Less than 4,000 rpm |
| A/F sensor status | Activated |
| Fuel cut | OFF (for 5 seconds or more) |
| Engine load | 10 to 80 % |
| Shift position | 4th or 5th (for M/T) 3rd, 4th or 5th (for A/T) |
| Battery voltage | 11 V or more |
| Estimated sensor temperature | Less than 700°C(1,292°F) |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Estimated sensor temperature | More than 450°C(842°F) |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Either of following conditions met: | 1 or 2 |
| 1. All of the following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| 2. All of the following conditions (d), (e) and (f) met | - |
| (d) Commanded air-fuel ratio | 14.9 or more |
| (e) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (f) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| All of the following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | Less than 0.21 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| All of the following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.9 or more |
| (b) Rear HO2 sensor voltage | More than 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| Duration of following condition met | 30 seconds or more |
| Heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition met | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or more |
| Duration of following condition met | 10 seconds or more |
| Heated oxygen sensor impedance | 1.2 V or more |
| Duration of following condition met | 30 seconds or more |
| Heated oxygen sensor voltage | Varies between 0.1 and 0.9 V |



| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 | +25% | Rich | More than 0.5 |
| O2S B1S2 | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.READ OUTPUT DTC |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC output) | Proceed to |
| P0138 | A |
| P0137 | B |
| P0136 | C |
|
| ||||
|
| ||||
| A | |
| 2.READ DATA LIST (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / O2S B1S2.
Allow the engine to idle.
Read the Heated Oxygen (HO2) sensor output voltage while idling.
| HO2 Sensor Output Voltages | Proceed to |
| More than 1.2 V | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch to OFF and wait for 5 minutes.
Disconnect the E4 ECM connector.
Check the resistance.
| Tester Connection | Specified Condition |
| HT1B (E4-2) - OX1B (E4-25) | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| NG | |
| 4.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the H3 HO2 sensor connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| +B (H3-2) - E2 (H3-4) | 10 kΩ or higher |
| +B (H3-2) - OX1B (H3-3) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | ||
| ||
| 5.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0138) |
On the intelligent tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0138 | A |
| No output | B |
|
| ||||
| A | ||
| ||
| 7.READ DATA LIST (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Start the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / O2S B1S2
After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.
Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 8.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136) |
On the intelligent tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0136 | A |
| No output | B |
|
| ||||
| A | |
| 10.REPLACE HEATED OXYGEN SENSOR |
| NEXT | |
| 11.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136) |
On the intelligent tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0136 | A |
| No output | B |
|
| ||||
| A | |
| 13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Warm up the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / INJ VOL.
Change the fuel injection volume using the tester, monitoring the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.
| Display (DTC Output) | Voltage Variations | Proceed To |
| AFS B1S1 (A/F) | Alternates between more and less than 3.3 V | OK |
| AFS B1S1 (A/F) | Remains at more than 3.3 V | NG |
| AFS B1S1 (A/F) | Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 14.CHECK FOR EXHAUST GAS LEAKAGE |
|
| ||||
| OK | |
| 15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H3 HO2 sensor connector.
Measure the resistance between the terminals of the HO2 sensor connector.
| Tester Connections | Specified Conditions |
| HT1B (H3-1) - +B (H3-2) | 11 to 16 Ω at 20°C (68°F) |
| HT1B (H3-1) - E2 (H3-4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 16.INSPECT EFI RELAY |
![]() |
Remove the EFI relay from the engine room R/B.
Check the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the EFI relay.
|
| ||||
| OK | |
| 17.CHECK HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the H3 HO2 sensor connector.
Turn the ignition switch to ON.
Measure the voltage between the +B terminal of the HO2 sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (H3-1) - Body ground | 9 to 14 V |
Turn the ignition switch to OFF.
Disconnect the E4 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT1B (H3-1) - HT1B (E4-2) | Below 1 Ω |
| OX1B (H3-3) - OX1B (E4-25) | Below 1 Ω |
| E2 (H3-4) - E2 (E4-28) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HT1B (H3-1) or HT1B (E4-2) - Body ground | 10 kΩ or higher |
| OX1B (H3-3) or OX1B (E4-25) - Body ground | 10 kΩ or higher |
| E2 (H3-4) or E2 (E4-28) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
Reconnect the ECM connectors.

|
| ||||
| OK | ||
| ||