Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

for Preparation Click here


DESCRIPTION


  1. G037115E02
    When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increase in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds.
    If the misfire exceeds the threshold levels, and could cause emission deterioration, the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Conditions
Trouble Areas
P0300
Simultaneous misfiring of several cylinders detected
(2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Air induction system
  9. Engine Coolant Temperature (ECT) sensor
  10. Compression pressure
  11. Valve clearance
  12. Valve timing
  13. PCV valve and hose
  14. PCV hose connections
  15. ECM
P0301
P0302
P0303
P0304
Misfiring of specific cylinder detected
(2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Air induction system
  8. Mass Air Flow (MAF) meter
  9. Engine Coolant Temperature (ECT) sensor
  10. Compression pressure
  11. Valve clearance
  12. Valve timing
  13. PCV valve and hose
  14. PCV hose connections
  15. ECM

HINT:
When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.
Reference: Inspection using an oscilloscope
With the engine idling, check the waveform between terminals #10 to #40 and E01 of the ECM connectors.

Items
Contents
Terminals
# 10 to # 40 - E01
Equipment Settings
20 V/Division, 100 or 1 ms/Division
Conditions
Idling

HINT:
The correct waveform is as shown.


A121608E01


MONITOR DESCRIPTION

The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1,000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1,000 crankshaft revolutions) occurs once.
  2. After the first 1,000 crankshaft revolutions, an excessive misfiring rate (approximately 20 to 50 misfires per 1,000 crankshaft revolutions) occurs 4 times in sequential crankshaft revolutions.
The ECM flashes the MIL and sets a DTC when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. In every 200 crankshaft revolutions at a high engine rpm, the threshold misfiring percentage is recorded once.
  2. In every 200 crankshaft revolutions at a normal engine rpm, the threshold misfiring percentage is recorded 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
Required Sensors/Components (Main)
Injector, Ignition coil, Spark plug
Required Sensors/Components (Related)
Crankshaft, Camshaft, Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1,000 to 4,000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaged misfire
MIL Operation
2 driving cycles: Emission related misfire
MIL flashes immediately: Catalyst damaged misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not present

Battery voltage
8 V or more
Throttle position learning
Completed
VVT system
Not operated by scan tool
Engine RPM
400 to 5,800 rpm
Both of following conditions A and B met
-
A. Engine coolant Temperature (ECT)
-10°C (14°F) or more
B. Either of following conditions 1 or 2 met
-
1. ECT at engine start
More than -7°C (19°F)
2. ECT
More than 20°C (68°F)

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-related-misfire: 
Misfire rate
1.538 % or more
Either of following conditions (a) or (b) met
-
(a) First 1,000 revolutions after engine start or check mode
Crankshaft 1,000 revolutions
(b) Except above
Crankshaft 1,000 revolutions x 4

Monitor Period of Catalyst-damaged-misfire (MIL blinks): 
Number of misfire per 200 revolutions
97.14 or more (varies with intake air amount and engine RPM)
Either of following conditions (a) or (b) met
-
(a) All of following conditions A, B and C met
Crankshaft 200 revolutions x 3
A. Driving cycles
1st
B. Check mode
OFF
C. Engine RPM
Below 2,200 rpm
(b) Except above
Crankshaft 200 revolutions

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM

Refer to DTC P0351 for the wiring diagram of the ignition system .

A121742E01


CONFIRMATION DRIVING PATTERN

  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester ON.
  4. Record the DTC(s) and freeze frame data.
  5. Using the tester, switch the ECM from normal mode to check mode.
  6. Read the misfire counts of each cylinder (CYL #1 to #4) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in MISFIRE RPM and MISFIRE LOAD in the DATA LIST.

    HINT:
    In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the MISFIRE RPM and MISFIRE LOAD in the DATA LIST.


    Engine RPM
    Duration
    Idling
    3.5 minutes or more
    1,000
    3 minutes or more
    2,000
    1.5 minutes or more
    3,000
    1 minute or more
  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch to OFF until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch to OFF and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than the misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data record the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel tank is low full.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
    4. The problem is complex.
  5. After finishing repairs, check the misfire counts of the cylinders (CYL #1, #2, #3 and #4).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine RPM. If misfires occur only in high engine RPM areas, only DTC P0300 is set.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the tester or scan tool.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
  8. When one of SHORT FT #1, LONG FT #1, SHORT FT #2 or LONG FT #2 in the freeze frame data is outside the range of +- 20 %, the air-fuel ratio may be rich (-20 % or less) or lean (+20 % or more).
  9. When the COOLANT TEMP in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC output)
    Proceed To
    P0300, P0301, P0302, P0303 and/or P0304
    A
    P0300, P0301, P0302, P0303 and/or P0304 and other DTCs
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.READ DATA LIST (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / MISFIRE RPM and MISFIRE LOAD.

  1. Read and note the MISFIRE RPM and MISFIRE LOAD (engine load) values.

    HINT:
    The MISFIRE RPM and MISFIRE LOAD indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK CONNECTION OF PCV HOSE

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.CHECK MISFIRE COUNT (CYL #1, #2, #3 AND #4)
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Turn the ignition switch to ON.
  3. (c) Turn the tester ON.
  4. (d) Clear DTCs (Click here).
  5. (e) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / CYL #1, #2, #3 and #4.
  6. (f) Allow the engine to idle.
  7. (g) Read each value of CYL #1 to #4 displayed on the tester. If no misfire counts occur in any cylinders, perform the following operations:
    1. (1) Shift the gear selector lever to the D position.
    2. (2) Repeat steps (e) to (g).
    3. (3) Check the CYL #1 to #4.
    4. (4) If misfire counts are still not displayed, perform steps (h) and (i) and then check the misfire counts again.
  8. (h) Drive the vehicle with the MISFIRE RPM and MISFIRE LOAD noted in step 2.
  9. (i) Read the CYL #1 to #4 or DTCs displayed on the tester.

    Result:

    Misfire Count
    Proceed To
    One or two cylinders have misfire counts
    A
    Three cylinders or more have misfire counts
    B



B
Go to step 13
A


5.CHECK SPARK PLUG
A088861E04
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard:
    Between 1.0 mm and 1.3 mm (0.039 in. and 0.051 in.)

  1. Check the electrode for carbon deposits.

    Recommended spark plug:
    Manufacturers
    Products
    DENSO
    SK20HR11
    NGK
    ILFR6C11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG
OK


6.CHECK SPARK AND IGNITION
G037116
  1. Disconnect the injector connectors, in order to prevent the engine from starting.

  1. Install the spark plug to the ignition coil.

  1. Attach the spark plug assembly to the cylinder head cover set bolt.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap

  1. Reconnect the injector connectors.



NG
Go to step 8
OK


7.CHECK CYLINDER COMPRESSION PRESSURE ON MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder.



OK
Go to step 9
NG

REPAIR OR REPLACE ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION 

8.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect each injector connector.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



OK
REPLACE SPARK PLUG
NG

REPLACE IGNITION COIL (THEN CONFIRM THAT THERE IS NO MISFIRE) 

9.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30,AND/OR #40 VOLTAGE)
A065741E09
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    #10 (E5-6) - E01 (E4-7)
    9 to 14 V
    #20 (E5-5) - E01 (E4-7)
    9 to 14 V
    #30 (E5-2) - E01 (E4-7)
    9 to 14 V
    #40 (E5-1) - E01 (E4-7)
    9 to 14 V



OK
Go to step 11
NG


10.CHECK HARNESS AND CONNECTOR (INJECTOR - ECM)
A113505E02
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the E4 and E5 ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the resistance and voltage between the injector and the ECM connector terminals.

    Standard Resistance and Standard Voltage (No.1 Cylinder):
    Tester Connections
    Specified Conditions
    F5-1 - Ground
    11 to 14 V
    F5-2 - Ground
    10 kΩ or higher
    F5-2 - #10 (E5-6)
    Below 1 Ω

    Standard Resistance and Standard Voltage (No.2 Cylinder):
    Tester Connections
    Specified Conditions
    F6-1 - Ground
    11 to 14 V
    F6-2 - Ground
    10 kΩ or higher
    F6-2 - #20 (E5-5)
    Below 1 Ω

    Standard Resistance and Standard Voltage (No.3 Cylinder):
    Tester Connections
    Specified Conditions
    F7-1 - Ground
    11 to 14 V
    F7-2 - Ground
    10 kΩ or higher
    F7-2 - #30 (E5-2)
    Below 1 Ω

    Standard Resistance and Standard Voltage (No.4 Cylinder):
    Tester Connections
    Specified Conditions
    F8-1 - Ground
    11 to 14 V
    F8-2 - Ground
    10 kΩ or higher
    F8-2 - #40 (E5-1)
    Below 1 Ω

  1. Reconnect the injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK FUEL INJECTOR (FUEL INJECTOR OF MISFIRING CYLINDER)
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


12.CHECK VALVE CLEARANCE (VALVE CLEARANCE OF MISFIRING CYLINDER)


NG
ADJUST VALVE CLEARANCE
OK


13.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage.

OK:
No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


14.CHECK VALVE TIMING
G038285E01
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the point marks on the camshaft timing gears are as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the marks as above.

    OK:
    Point marks on camshaft timing gears are aligned as shown in illustration.

  1. Reinstall the cylinder head cover .



NG
ADJUST VALVE TIMING
OK


15.CHECK FUEL PRESSURE
  1. Check the fuel pressure.



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


16.READ DATA LIST (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.

  1. Read the COOLANT TEMP twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 95°C (167°F and 203°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


17.READ DATA LIST (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / MAF and COOLANT TEMP.

  1. Allow the engine to idle until the COOLANT TEMP reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.

Standard:
MAF while engine idling: Between 2.0 g/sec and 4.5 g/sec (shift position: N, A/C: OFF).
MAF at engine speed of 2,500 rpm: Between 8.0 g/sec and 14.7 g/sec (shift position: N, A/C: OFF).



NG
REPLACE MASS AIR FLOW METER
OK

CHECK FOR INTERMITTENT PROBLEMS