Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
According to the DATA LIST displayed on the intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the DATA LIST as the first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Push the "ON" button of the tester.

  6. Select the items "DIAGNOSIS/ ENHANCED OBD II/ DATA LIST/ A/T".

  7. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/
    Display (Range)
    Normal Condition
    Diagnostic Note
    SPD (NCO)
    Input Speed display: 50 rpm

    HINT:
    1. 3rd Gear Lock-up ON (After warming up the engine);
      Input turbine speed (NCO) equal to the engine speed
    2. 4th Gear Lock-up ON (After warming up the engine);
      Input turbine speed (NCO): 0 rpm
    3. Lock-up OFF (Idling at N position);
      Input turbine speed (NCO) nearly equal to the engine speed

    -
    SPD (SP2)
    Counter Gear Speed display/
    min.: 0 mph (0 km/h)
    max.: 158 mph (255 km/h)
    Vehicle stopped: 0 mph (0 km/h)
    -
    PNP SW [NSW]
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    P or N: ON
    Except P and N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    STOP LIGHT SW
    Stop Lamp Switch Status/
    ON or OFF
    1. Brake Pedal is depressed: ON
    2. Brake Pedal is released: OFF
    -
    SHIFT
    Actual Gear Position/
    1st, 2nd, 3rd or 4th
    Shift Lever Position is;
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. D: 1st, 2nd, 3rd or 4th
    -
    REVERSE
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    DRIVE
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    D and 3: ON
    Except D and 3: OFF
    3RD
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    3: ON
    Except 3: OFF
    2ND
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    2: ON
    Except 2: OFF
    LOW
    PNP SW Status/
    ON or OFF
    Shift lever position is;
    L: ON
    Except L: OFF
    A/T OIL TEMP1
    ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approximately 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temperature sensor circuit is open or short.
    A/T OIL TEMP3
    ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approximately 80°C (176°F)
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temperature sensor circuit is open or short.
    ATF
    ATF Condition
    ATF Condition
    NG: ON
    OK: OFF
    Replace ATF when ATF condition is ON.
    LOCK UP SOL
    Lock-up solenoid status/ ON or OFF
    1. Lock-up: ON
    2. Except lock-up: OFF
    -
    SOLENOID (SLT)
    Shift Solenoid SLT Status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SOLENOID (SLU)
    Shift Solenoid SLU Status/
    ON or OFF
    1. Lock-up: ON
    2. Except Lock-up: OFF
    -


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one method of shortening labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Push the "ON" button of the tester.

  6. Select the items "DIAGNOSIS/ ENHANCED OBD II/ ACTIVE TEST".

  7. According to the display on the tester, perform the "ACTIVE TEST".

    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set each shift position manually.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 31 mph (50 km/h)
    [Others]
    1. Press → button: Shift up
    2. Press ← button: Shift down
    Possible to check the operation of the shift solenoid valves.
    LOCK UP
    [Test Details]
    Control the shift solenoid SLU to set the automatic transmission to the lock-up condition.
    [Vehicle Condition]
    Vehicle Speed: 37 mph (60 km/h) or more
    Possible to check the SLU operation.
    LINE PRESS UP *
    [Test Details]
    Operate the shift solenoid SLT to raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped
    2. IDL: ON

    HINT:
    OFF: Line pressure up (When the active test of "LINE PRESS UP" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)

    -
    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in the ACTIVE TEST and HYDRAULIC TEST are different from each other.