Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor assembly and the seat position sensor.
DTC B1653/35 is set when a malfunction is detected in the seat position sensor assembly circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor assembly circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 1 seat wire (*1)
  3. No. 2 seat wire (*1)
  4. Front seat belt inner assembly LH (*2)
  5. Seat position sensor
  6. Center airbag sensor assembly
*1: Bench seat
*2: Separate seat

WIRING DIAGRAM


H101960E02


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat outer belt assembly LH.
  7. (g) Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  8. (h) Disconnect the connector from the front seat airbag assembly LH.
  9. (i) Disconnect the connector from the front seat airbag assembly RH.
  10. (j) Disconnect the connector from the curtain shield airbag assembly LH.
  11. (k) Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK DTC


    H102111E01
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and seat position sensor side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.

    Condition
    Proceed to
    Normal (separate seat)
    A
    Normal (bench seat)
    B
    Abnormal
    C



B
Go to step 13

C
REPAIR OR REPLACE WIRE HARNESS
A


4.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN)


    H102105E01
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position sensor.

  1. Using a service wire, connect 1 and 2 of connector E.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

HINT:
The connector is not allocated an ID number due to being part of the front seat inner belt assembly LH wire harness.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - A22-13 (DSP-)
    Always
    Below 1 Ω



NG
Go to step 9
OK


5.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT)


    H101853E01
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - A22-13 (DSP-)
    Always
    1 MΩ or Higher



NG
Go to step 10
OK


6.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+)


    H101853E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    A22-13 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 11
OK


7.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND)


    H101853E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    A22-13 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 12
OK


8.CHECK SEAT POSITION SENSOR


    H100890E04
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the seat position sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 26
OK

USE SIMULATION METHOD TO CHECK 

9.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN)


    H102106E01
  1. Disconnect the front seat inner belt assembly connector from the instrument panel wire.

HINT:
  1. The service wire has already been inserted into connector E.
  2. The connector is not allocated an ID number due to being part of the front seat inner belt assembly LH wire harness.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (DSP+) - 4 (DSP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

10.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT)


    H046112E03
  1. Disconnect the front seat inner belt assembly connector from the instrument panel wire.

HINT:
The connector is not allocated an ID number due to being part of the front seat inner belt assembly LH wire harness.

  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (DSP+) - 4 (DSP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

11.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+)


    H046112E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the seat inner belt assembly LH connector from the instrument panel wire.

HINT:
The connector is not allocated an ID number due to being part of the front seat inner belt assembly LH wire harness.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    4 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

12.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND)


    H046112E03
  1. Disconnect the front seat inner belt assembly connector from the instrument panel wire.

HINT:
The connector is not allocated an ID number due to being part of the front seat inner belt assembly LH wire harness.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    4 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

13.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN)


    H102107E01
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position sensor.

  1. Using a service wire, connect S25-1 and S25-2 of connector G.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - A22-13 (DSP-)
    Always
    Below 1 Ω



NG
Go to step 18
OK


14.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT)


    H101963E02
  1. Disconnect the service wire from connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - A22-13 (DSP-)
    Always
    1 MΩ or Higher



NG
Go to step 19
OK


15.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+)


    H101963E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    A22-13 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 20
OK


16.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND)


    H101963E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-14 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    A22-13 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 21
OK


17.CHECK SEAT POSITION SENSOR


    H102108E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the seat position sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 26
OK

USE SIMULATION METHOD TO CHECK 

18.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN)


    H102109E01
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

HINT:
The service wire has already been inserted into connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - BK1-4 (DSP-)
    Always
    Below 1 Ω



NG
Go to step 22
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

19.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT)


    H101966E02
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - BK1-4 (DSP-)
    Always
    1 MΩ or Higher



NG
Go to step 23
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

20.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+)


    H101966E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    BK1-4 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 24
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

21.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND)


    H101966E02
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    BK1-4 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 25
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

22.CHECK NO.1 SEAT WIRE (FOR OPEN)


    H102110E01
  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

HINT:
The service wire has already been inserted into connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-2 (DSP+) - BL1-1 (DSP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

23.CHECK NO.1 SEAT WIRE (FOR SHORT)


    H101968E02
  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-2 (DSP+) - BL1-1 (DSP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

24.CHECK NO.1 SEAT WIRE (TO B+)


    H101968E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    BL1-2 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    BL1-1 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

25.CHECK NO.1 SEAT WIRE (TO GROUND)


    H101968E02
  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-2 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    BL1-1 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

26.REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position sensor (Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


27.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H102111E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END