Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1820/55    Short in Driver Side - Side Squib Circuit

DTC    B1821/55    Open in Driver Side - Side Squib Circuit

DTC    B1822/55    Short to GND in Driver Side - Side Squib Circuit

DTC    B1823/55    Short to B+ in Driver Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The side squib (driver seat side) circuit consists of the center airbag sensor assembly and the front seat with adjuster frame assembly LH.
This circuit signals the SRS to deploy when airbag deployment conditions are met.
These DTCs are set when a malfunction is detected in the side squib (driver seat side) circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1820/55
  1. The center airbag sensor assembly receives a line short circuit signal in the side squib (Driver seat side) circuit for 2 seconds
  2. Side squib (Driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat with adjuster frame assembly LH (Side squib (Driver seat side))
  3. Center airbag sensor assembly
B1821/55
  1. The center airbag sensor assembly receives an open circuit signal in the side squib (Driver seat side) circuit for 2 seconds
  2. Side squib (Driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat with adjuster frame assembly LH (Side squib (Driver seat side))
  3. Center airbag sensor assembly
B1822/55
  1. The center airbag sensor assembly receives a short circuit to ground signal in the side squib (Driver seat side) circuit for 0.5 seconds
  2. Side squib (Driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat with adjuster frame assembly LH (Side squib (Driver seat side))
  3. Center airbag sensor assembly
B1823/55
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the side squib (Driver seat side) circuit for 0.5 seconds
  2. Side squib (Driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat with adjuster frame assembly LH (Side squib (Driver seat side))
  3. Center airbag sensor assembly

WIRING DIAGRAM


H101930E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. If using the intelligent tester (read the 5-digit DTCs):
      Using the intelligent tester, check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC B1820 is output.
      A
      DTC B1821 is output.
      B
      DTC B1822 is output.
      C
      DTC B1823 is output.
      D

    2. If not using the intelligent tester (read the 2-digit DTCs): Check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC 55 is output.
      E



B
Go to step 3

C
Go to step 4

D
Go to step 5

E
Go to step 6
A


2.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H100872E04
  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - S26-2 (SFD-)
    Always
    1 MΩ or Higher



OK
Go to step 8
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

3.CHECK NO. 2 FLOOR WIRE (FOR OPEN)


    H100872E04
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - S26-2 (SFD-)
    Always
    Below 1 Ω



OK
Go to step 9
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

4.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H100872E04
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - Body ground
    Always
    1 MΩ or Higher
    S26-2 (SFD-) - Body ground
    Always
    1 MΩ or Higher



OK
Go to step 9
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

5.CHECK NO. 2 FLOOR WIRE (TO B+)


    H100872E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - Body ground
    Ignition switch ON
    Below 1 V
    S26-2 (SFD-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 9
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

6.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB (DRIVER SEAT SIDE) CIRCUIT)


    H100872E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - Body ground
    Ignition switch ON
    Below 1 V
    S26-2 (SFD-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - S26-2 (SFD-)
    Always
    Below 1 Ω
    S26-1 (SFD+) - Body ground
    Always
    1 MΩ or Higher
    S26-2 (SFD-) - Body ground
    Always
    1 MΩ or Higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S26-1 (SFD+) - S26-2 (SFD-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


7.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH (SIDE SQUIB (DRIVER SEAT SIDE))


    H100873E01
  1. Replace the front seat with adjuster frame assembly LH (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 55 is not output.

HINT:
DTCs other than 55 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END 

8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C109222E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820 is not output.

HINT:
DTCs other than B1820 may be output at this time, but they are not related to this check.



OK
Go to step 10
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

9.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 5, begin from (a). If continuing from any other step, begin from (c).



    H101871E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect S26-1 (SFD+) and S26-2 (SFD-) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1821, B1822 and B1823 are not output.

HINT:
DTCs other than B1821, B1822 or B1823 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


10.CHECK FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH
C109223E01

HINT:
If continuing from step 9, begin from (c). If continuing from any other step, being from (a).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat with adjuster frame assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822 and B1823 are not output.

HINT:
DTCs other than B1820, B1821, B1822 or B1823 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH
OK

USE SIMULATION METHOD TO CHECK