Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. INSTALL ROOF WIRE


    B087428E02
  1. w/ EC mirror:

    1. Install the roof wire with 8 new tapes, as shown in the illustration.

  1. w/o EC mirror:

    1. Install the roof wire with 8 new tapes, as shown in the illustration.



2. INSTALL ROOF HEADLINING PAD


    B087429E02
  1. Install 2 new roof headlining pads onto the roof headlining.



3. INSTALL ROOF HEADLINING ASSEMBLY


    B087430E01
  1. Install the roof headlining into the vehicle.



    B087645E01
  1. Install the 2 wire harness clamps.

  1. Connect the roof wire connector.

  1. Connect the frame wire connector.



4. INSTALL COAT HOOK


B087466E02

HINT:
Follow the same procedures as for the opposite side.

  1. Turn the coat hook 90° clockwise and install it.



5. INSTALL VISOR HOLDER


B087467E02

HINT:
Follow the same procedures as for the opposite side.

  1. Turn the visor holder 90° clockwise and install it.



6. INSTALL VISOR ASSEMBLY LH


    B087457
  1. Install the visor into the visor holder.

  1. Tighten the 2 screws.



7. INSTALL VISOR ASSEMBLY RH

HINT:
Follow the same procedures as for the visor assembly LH.



8. INSTALL ASSIST GRIP PLUG (w/ Curtain Shield Airbag)


B087592E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the claw and install the assist grip plug.

  1. Tighten the screw.



    B087594E01
  1. Engage the 2 claws and close the cover.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY


B087423E01

HINT:
Follow the same procedures as for the opposite side.

  1. Install the assist grip with the 2 screws.



    B087431E01
  1. Engage the 2 claws and close the cover.



10. INSTALL ROOF CONSOLE BOX ASSEMBLY


    B087595E01
  1. Install the wire harness clamp.



    B087456E01
  1. Connect the accessory meter connector and map lamp connector.

  1. Engage the 2 clips and 3 claws and install the map lamp.

  1. Tighten the screw.



11. INSTALL ROOM LIGHT ASSEMBLY


    B087468E01
  1. Connect the room light connector.

  1. Engage the 3 claws and install the room light.



    B087469E01
  1. Engage the 2 claws and install the room light lens.



12. INSTALL QUARTER INSIDE TRIM BOARD LH


    B087421E01
  1. Engage the 2 clips and install the quarter inside trim board.

  1. Tighten the 3 screws.



    B087432E01
  1. Engage the claw and close the cover.



    B087330E02
  1. Install the floor anchor of the rear seat belt outer with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat outer belt is oriented in the correct direction when installing.
    2. Be careful not to place the rear seat outer belt over the convex areas of the floor panel.



13. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the quarter inside trim board LH.



14. INSTALL QUARTER TRIM LOWER PANEL LH


    B087419E01
  1. Engage the 2 claws and 2 clips, and install the quarter trim lower panel.



15. INSTALL QUARTER TRIM LOWER PANEL RH

HINT:
Follow the same procedures as for the quarter trim lower panel LH.



16. INSTALL LUGGAGE COMPARTMENT SIDE TRAY RH


    B087580E01
  1. w/ Woofer:

    1. Engage the 5 claws and 7 clips, and install the luggage compartment side tray.

    2. Tighten the bolt.



    B087581E01
  1. w/o Woofer:

    1. Engage the 5 claws and 5 clips, and install the luggage compartment side tray.

    2. Tighten the 3 bolts.



17. INSTALL REAR SEAT BACK CENTER HINGE SUB-ASSEMBLY


    B087197E01
  1. Install the rear seat back center hinge with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 14 ft.*lbf }



18. INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH


    B087579E01
  1. Engage the 8 claws and 3 clips, and install the luggage compartment side tray.

  1. Tighten the 3 bolts.



19. INSTALL CENTER PILLAR UPPER GARNISH LH


    B087418E01
  1. Engage the clip and install the center pillar upper garnish.

  1. Tighten the 2 screws.



20. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:
Follow the same procedures as for the center pillar upper garnish LH.



21. INSTALL CENTER PILLAR LOWER GARNISH LH


    B087417E01
  1. Engage the 2 claws and 2 clips, and install the center pillar lower garnish.



    B087416E01
  1. Install the floor anchor of the front seat outer belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



22. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:
Follow the same procedures as for the center pillar lower garnish LH.



23. INSTALL LAP BELT OUTER ANCHOR COVER


B087415E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 3 claws and install the lap belt outer anchor cover.



24. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel sub-assembly w/ passenger air bag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.



  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.


    B085804E01



25. CONNECT PASSENGER AIRBAG CONNECTOR


26. INSTALL INSTRUMENT SIDE PANEL


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



27. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Connect the 2 connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



28. INSTALL INSTRUMENT LOWER PANEL


    B085788E01
  1. Install the lower instrument panel LH with the 3 bolts <B>.



29. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY


    B085787E01
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



30. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B085815E01
  1. Install the glow compartment door assembly with 3 hinges, holding it horizontal.



    B085785E01
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stopper onto the glove compartment door.



31. INSTALL INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



32. INSTALL COMBINATION METER ASSEMBLY


    B085782E01
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws <E>.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



33. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B085781E01
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



34. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



35. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



36. INSTALL RADIO RECEIVER ASSEMBLY


E075957
  1. Connect the connector.

  1. Install the radio receiver assembly with bracket with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



37. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


B085779E01
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



38. INSTALL FRONT CONSOLE BOX
  1. for Automatic Transmission:

    1. Install the front console box .

  1. for Manual Transmission:

    1. Install the front console box .



39. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission)


    B085773E01
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.



40. INSTALL REAR CONSOLE BOX ASSEMBLY


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



41. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. for Automatic Transmission:

    1. Install the rear console upper panel sub-assembly .

  1. for Manual Transmission:

    1. Install the rear console upper panel sub-assembly .



42. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



43. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Engage the 4 clips and install the instrument panel hole cover.



44. INSTALL FRONT PILLAR GARNISH LH


    B087596E01
  1. Install the 3 wire harness clamps (LH side only).



    B087444E01
  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



45. INSTALL FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



46. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B087414E01
  1. Install the rear door opening trim weatherstrip.



47. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the rear door opening trim weatherstrip.



48. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B087413E01
  1. Install the front door opening trim weatherstrip.



49. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip.



50. INSTALL REAR DOOR SCUFF PLATE LH


    B087412E01
  1. Engage the 8 claws and install the rear door scuff plate.



51. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the rear door scuff plate LH.



52. INSTALL COWL SIDE TRIM BOARD LH


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



53. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



54. INSTALL FRONT DOOR SCUFF PLATE LH


    B087411E01
  1. Engage the 9 claws and install the front door scuff plate.



55. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



56. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY LH


    B087196E01
  1. Install the rear seat back hinge with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 14 ft.*lbf }



57. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT:
Follow the same procedures as for the rear seat back hinge sub-assembly LH.



58. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



59. INSTALL REAR SEAT BACK ASSEMBLY LH


    B087195E01
  1. Install the rear seat back with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



60. INSTALL REAR SEAT BACK ASSEMBLY RH


    B087217
  1. Install the rear seat back with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B087239E03
  1. Install the rear seat belt inner and rear seat belt outer center of the floor anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat inner belt and floor anchor of the rear center seat outer belt are oriented in the correct direction when installing.
    2. Be careful not to place the rear seat inner belt (and floor anchor of the rear center seat outer belt) over the convex areas of the floor panel.



61. INSTALL REAR SEAT BACK HINGE COVER
  1. for LH Side:

    1. Install the rear seat back hinge cover .

  1. for RH Side:

    1. Install the rear seat back hinge cover .



62. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    B087193E01
  1. Install the rear seat cushion with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



63. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    B087214E01
  1. Install the rear seat cushion with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



64. INSTALL FRONT SEAT ASSEMBLY LH


    B087375E01
  1. Place the front seat in the cabin.

  1. Tighten the 2 bolts on the front side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Tighten the 2 bolts on the rear side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B087646E01
  1. Install the wire harness clamp.

  1. Connect the 2 connectors.

  1. w/ Front Seat Side Airbag:

    1. Connect the connector.



65. INSTALL FRONT SEAT ASSEMBLY RH
  1. for Separate Folding Seat Type:

    1. Install the front seat assembly RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Install the front seat assembly RH .



66. INSTALL SEAT TRACK COVER LH


B087374E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the seat track cover.



67. INSTALL SEAT TRACK COVER RH
  1. for Separate Folding Seat Type:

    1. Install the seat track cover RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Install the seat track cover RH .



68. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


    B087585E01
  1. Engage the 2 claws and install the inner rear view mirror cover.



    B087586E01
  1. Slide and install the inner rear view mirror.



    B087587E01
  1. Slide the inner rear view mirror cover.

  1. Connect the EC mirror connector.



69. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



70. INSPECT SRS WARNING LIGHT
(Click here)