Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT (for 4WD)

FRONT DRIVE SHAFT (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT


F042771
  1. Coat the spline of the inboard joint shaft with ATF.

  1. Align the shaft splines and install the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Be careful not to damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



2. INSTALL FRONT SUSPENSION LOWER ARM


G020159
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf }



3. INSTALL FRONT AXLE HUB NUT


F042732
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and a new cotter pin.

  1. Install the front axle hub grease cap.



4. INSTALL TIE ROD END SUB-ASSEMBLY
  1. Install the tie rod end onto the steering knuckle.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



5. INSTALL FRONT SPEED SENSOR


F052163E03
  1. Install the speed sensor wire harness onto the steering knuckle with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Engage the 2 clamps.

  1. Install the speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



6. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



7. INSPECT DIFFERENTIAL OIL


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

(Click here)


9. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)


10. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)


11. CHECK FOR DIFFERENTIAL OIL LEAKAGE


12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)