ANTI-LOCK BRAKE SYSTEM > TEST MODE PROCEDURE |
| TEST MODE PROCEDURE (for Using a Intelligent Tester) |
Turn the ignition switch to OFF.
Check that the steering wheel is in the straight-ahead position.
A/T: Check that the shift lever is in the P position and apply the parking brake.
M/T: Check that the shift lever is in neutral and apply the parking brake.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Switch the ECU to test mode using the intelligent tester.
Select the following menu items: DIAGNOSIS / OBD/MOBD / select vehicle / ABS/VSC / SIGNAL CHECK.

![]() |
Check that the ABS warning light blinks as shown in the illustration.
| Trouble Areas | See Page |
| ABS warning light circuit |
Click here
Click here |
| TS and CG terminal circuit |
Click here
|
Start the engine.
Active the ABS sensor (deceleration sensor, 4WD detection switch, L4 detection switch and speed sensor) in test mode (SIGNAL CHECK) using intelligent tester.
| TEST MODE PROCEDURE (for Using a SST Check Wire) |
Turn the ignition switch to OFF.
Check that the steering wheel is in the straight-ahead position.
A/T: Check that the shift lever is in the P position and apply the parking brake.
M/T: Check that the shift lever is in neutral and apply the parking brake.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
| Trouble Areas | See Page |
| ABS warning light circuit |
Click here
Click here |
| TS and CG terminal circuit |
Click here
|
Start the engine.
Activate the ABS sensor (deceleration sensor, 4WD detection switch, L4 detection switch and speed sensor) in test mode (SIGNAL CHECK) using a check wire.
| DECELERATION SENSOR SIGNAL CHECK (for 4WD and Pre-runner) |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Keep the vehicle stationary on a level surface for 1 second or more.
| 4WD DETECTION SWITCH SIGNAL CHECK (for 4WD) |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the transfer indicator switch (4WD position).
Push the 4 wheel drive control switch on to put the vehicle in 4WD mode.
Push the 4 wheel drive control switch off to put the vehicle in 2WD mode.
| L4 DETECTION SWITCH SIGNAL CHECK (for 4WD) |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the transfer indicator switch (L4 position).
Turn the 4 wheel drive control switch to the L position to put the vehicle in L4 mode.
Turn the 4 wheel drive control switch to the H position to put the vehicle in H4 mode.
| SPEED SENSOR CHECK |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check thee speed sensor signal.
Drive the vehicle straight forward at a speed of 56 mph (90 km/h) or more.
Drive the vehicle straight rearward at a speed of 1.9 mph (3 km/h) or more for 1 second or more.
Check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC OF ABS SENSOR (for Using a Intelligent Tester) |
Read the DTC(s) by following the tester screen.
| READ DTC OF ABS SENSOR (for Using a SST Check Wire) |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Turn the ignition switch to the ON position.
Read the number of blinks of the ABS warning light.
![]() |

After the check, disconnect the SST from terminals TC and CG of the DLC3.
Turn the ignition switch to OFF.
| DTC OF SIGNAL CHECK FUNCTION |
| DTC No. | Diagnosis | Trouble Areas |
| C1271/71 | Low output voltage of right front speed sensor |
|
| C1272/72 | Low output voltage of left front speed sensor |
|
| C1273/73 | Low output voltage of right rear speed sensor |
|
| C1274/74 | Low output voltage of left rear speed sensor |
|
| C1275/75 | Abnormal change in output voltage of right front speed sensor | Right front speed sensor rotor |
| C1276/76 | Abnormal change in output voltage of left front speed sensor | Left front speed sensor rotor |
| C1277/77 | Abnormal change in output voltage of right rear speed sensor | Right rear speed sensor rotor |
| C1278/78 | Abnormal change in output voltage of left rear speed sensor | Left rear speed sensor rotor |
| C1279/79 (*1), (*2) | Deceleration sensor faulty |
|
| C1282/82 (*2) | Center differential lock position switch malfunction | Transfer indicator switch (4WD position) |
| C1283/83 (*2) | L4 detection switch malfunction | Transfer indicator switch (L4 position) |