Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB (for 4WD and Pre-Runner)

FRONT AXLE HUB (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE HUB


2. INSTALL FRONT SUSPENSION UPPER ARM


G020157
  1. Install a new nut and clip.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }



3. INSTALL FRONT SUSPENSION LOWER ARM


F051497
  1. Install the front suspension lower arm with the 2 bolts.

    Torque:
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf }



4. INSTALL TIE ROD END SUB-ASSEMBLY


F043604
  1. Install the tie rod end with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.



5. INSTALL FRONT STABILIZER LINK ASSEMBLY


C099158
  1. Install the stabilizer link onto the steering knuckle with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



6. INSTALL FRONT AXLE HUB NUT (for 4WD)


F042732
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and cotter pin.



7. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)


8. INSTALL FRONT DISC


9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


F043121
  1. Install the front disc brake caliper with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



    F052164
  1. Install the brake tube bracket onto the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F043120
  1. Using SST, connect the brake tube to the disc brake cylinder.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



10. INSTALL FRONT SPEED SENSOR


F052163E03
  1. Install the speed sensor wire harness onto the steering knuckle with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Engage the 2 clips.

  1. Install the speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



11. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

(Click here)


13. FILL RESERVOIR WITH BRAKE FLUID (w/ VSC)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



14. FILL RESERVOIR WITH BRAKE FLUID (w/o VSC)


F050555

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



15. BLEED MASTER CYLINDER (w/o VSC)


F050556

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. Using SST, disconnect the brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress the brake pedal and hold it there (step A).



    F050557
  1. Block the outer holes with your fingers, and release the brake pedal (step B).

  1. Repeat step A and B 3 or 4 times.



16. BLEED BRAKE LINE (w/ VSC)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



17. BLEED BRAKE LINE (w/o VSC)


F050558
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step D).

  1. Repeat step C and D until all the air in the fluid has been bled out.

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



18. CHECK FLUID LEVEL IN RESERVOIR (w/ VSC)
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).



19. CHECK FLUID LEVEL IN RESERVOIR (w/o VSC)
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS NO. 116 DOT3



20. CHECK FOR BRAKE FLUID LEAKAGE


21. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)


22. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)


23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)