Home › SUSPENSION & AXLE › AXLE › REAR AXLE SHAFT

REAR AXLE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE SHAFT OIL SEAL


F052141E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09950-60020   (09951-00770)
    09950-70010   (09951-07150)



2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE


F052131
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL REAR BRAKE TUBE NO. 8


F052272
  1. Using SST, connect the brake tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



4. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 3


D028121
  1. Install the parking brake cable with the 2 bolts onto the backing plate.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL REAR SPEED SENSOR


F050583
  1. Install the rear speed sensor with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



6. APPLY HIGH TEMPERATURE GREASE


F050548
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



7. INSTALL REAR BRAKE SHOE


F050549
  1. Apply high temperature grease to the adjusting bolt.



    F050550
  1. Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.



    F050544
  1. Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.



    F042688
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F050543E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



8. INSTALL FRONT BRAKE SHOE
  1. Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.



    F050542E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring onto the front brake shoe and rear brake shoe.



    F050551
  1. Using needle-nose pliers, install the return spring.



    F050540E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00010  



9. INSPECT REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.


    F050552E01



    F050553E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.

    Shoe clearance:
    0.5 mm (0.020 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



10. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install a new drum gasket onto the rear brake drum.

  1. Install the rear brake drum.



11. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



12. INSTALL REAR WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

(Click here)


14. FILL RESERVOIR WITH BRAKE FLUID (w/ VSC)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



15. FILL RESERVOIR WITH BRAKE FLUID (w/o VSC)


F050555

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



16. BLEED MASTER CYLINDER (w/o VSC)


F050556

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. Using SST, disconnect the brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress the brake pedal and hold it there (step A).



    F050557
  1. Block the outer holes with your fingers, and release the brake pedal (step B).

  1. Repeat step A and B 3 or 4 times.



17. BLEED BRAKE LINE (w/ VSC)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



18. BLEED BRAKE LINE (w/o VSC)


F050558
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step D).

  1. Repeat step C and D until all the air in the fluid has been bled out.

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



19. CHECK FLUID LEVEL IN RESERVOIR (w/ VSC)
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).



20. CHECK FLUID LEVEL IN RESERVOIR (w/o VSC)
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS NO. 116 DOT3



21. CHECK FOR BRAKE FLUID LEAKAGE


22. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



23. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



24. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



25. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.



26. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)


27. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)