Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY


F051366E01
  1. Remove any dust and oil from the differential carrier assembly and contact surface of the axle housing.

  1. Apply liquid gasket to both sides of the gasket.

    NOTICE:
    Do not put the liquid gasket on the stud bolt.



    F052203E01
  1. Install a new gasket and the differential carrier assembly with the 10 nuts and 10 washers.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH


F052131
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL NO.3 PARKING BRAKE CABLE ASSEMBLY


F050655
  1. Install the parking brake cable with the clip onto the parking brake equalizer.



  1. Install the parking brake cable with the 4 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    F050710E01



    F050711E01



    F050712E01



    D028121
  1. Install the parking brake cable with the 2 bolts onto the backing plate.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL NO.2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure as for the LH side.



6. INSTALL REAR SPEED SENSOR LH


F050583
  1. Install the rear speed sensor with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



7. INSTALL REAR SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD Drive Type, Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



9. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 2WD Drive Type, Except Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



10. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD Driver Type, Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C060588E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD Driver Type, Expect Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098708E02
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



12. INSTALL REAR BRAKE SHOE


F050549
  1. Apply high temperature grease to the adjusting bolt.



    F050550
  1. Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.



    F050544
  1. Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.



    F042688
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F050543E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



13. INSTALL FRONT BRAKE SHOE
  1. Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.



    F050542E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring onto the front brake shoe and rear brake shoe.



    F050551
  1. Using needle-nose pliers, install the return spring.



    F050540E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00010  



14. INSPECT REAR BRAKE DRUM INSTALLATION


  1. Check that each part is installed properly.


    F050552E01



    F050553E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.

    Shoe clearance:
    0.5 mm (0.020 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



15. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install a new drum gasket onto the rear brake drum.

  1. Install the rear brake drum.



16. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



17. FILL RESERVOIR WITH BRAKE FLUID (w/ VSC)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



18. FILL RESERVOIR WITH BRAKE FLUID (w/o VSC)


F050555

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



19. BLEED MASTER CYLINDER (w/o VSC)


F050556

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. Using SST, disconnect the brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress the brake pedal and hold it there (step A).



    F050557
  1. Block the outer holes with your fingers, and release the brake pedal (step B).

  1. Repeat step A and B 3 or 4 times.



20. BLEED BRAKE LINE (w/ VSC)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



21. BLEED BRAKE LINE (w/o VSC)


F050558
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step D).

  1. Repeat step C and D until all the air in the fluid has been bled out.

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



22. CHECK FLUID LEVEL IN RESERVOIR (w/ VSC)
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).



23. CHECK FLUID LEVEL IN RESERVOIR (w/o VSC)
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS NO. 116 DOT3



24. CHECK FOR BRAKE FLUID LEAKAGE


25. ADD DIFFERENTIAL OIL


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



26. INSPECT DIFFERENTIAL OIL


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



27. INSPECT FOR DIFFERENTIAL OIL LEAKAGE


28. INSTALL REAR WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 in.*lbf }



29. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



30. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



31. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



32. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.



33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



34. CHECK VSC SENSOR SIGNAL (w/ VSC)

HINT:
(Click here)



35. CHECK ABS SENSOR SIGNAL (w/o VSC)

HINT:
(Click here)