Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY


C097020
  1. Connect the actuator hose and connector.

  1. Install the No. 1 mounting support with the 3 bolts.

    Torque:
    186 N*m{ 1,899 kgf*cm , 138 ft.*lbf }

  1. Install the No. 2 mounting support with the 2 bolts.

    Torque:
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf }

  1. Install the No. 3 front differential support with the 2 bolts.

    Torque:
    108 N*m{ 1,100 kgf*cm , 80 ft.*lbf }

  1. Support the front differential with a jack.

  1. Install the 2 front mounting bolts and nuts.

    Torque:
    137 N*m{ 1,400 kgf*cm , 101 ft.*lbf }

  1. Install the No. 1 front differential mount nut.

    Torque:
    87 N*m{ 889 kgf*cm , 64 ft.*lbf }

  1. Install the front differential breather tube bracket with the bolt.

    Torque:
    13 N*m{ 129 kgf*cm , 8 ft.*lbf }

  1. Lower the jack.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


F042739E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Be careful not to damage the oil seal.



3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL FRONT SUSPENSION LOWER ARM LH


G020159
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf }



5. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Install the tie rod end onto the steering knuckle arm.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



7. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



8. INSTALL FRONT SPEED SENSOR LH


C114967E02
  1. Install the front speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



9. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


G020162
  1. Install the front stabilizer bracket with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL FRONT AXLE HUB LH NUT


F042732
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and cotter pin.



13. INSTALL FRONT AXLE HUB RH NUT

HINT:
Use the same procedure as for the LH side.



14. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


C098708E03
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



15. ADD DIFFERENTIAL OIL


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



16. INSPECT DIFFERENTIAL OIL


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



17. INSPECT FOR DIFFERENTIAL OIL LEAKAGE


18. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 2 engine under cover sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



19. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



20. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



23. CHECK VSC SENSOR SIGNAL (w/ VSC)

HINT:
(Click here)



24. CHECK ABS SENSOR SIGNAL (w/o VSC)

HINT:
(Click here)