Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › TIMING CHAIN (for 4WD and Pre-Runner)

TIMING CHAIN (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL CHAIN TENSIONER SLIPPER


2. INSTALL NO.1 CHAIN TENSIONER ASSEMBLY


A076294E02
  1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 35 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Install the chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }



3. INSTALL CHAIN SUB-ASSEMBLY


G036290E03


  1. Set the No. 1 cylinder to TDC/ compression.

    1. Align the timing marks of the camshaft timing gears and bearing caps.



    2. A076296E02
    3. Using the crankshaft pulley set bolt, turn the crankshaft to align the crankshaft set key with the timing line of the cylinder block.



    A076297E03
  1. Align the yellow mark link with the timing mark of the crankshaft timing link.



    G036259E02
  1. Align the orange mark links with the timing marks of the camshaft timing gears, and install the chain.



4. INSTALL NO.2 CHAIN VIBRATION DAMPER
  1. Install the 2 chain vibration dampers No. 2.



5. INSTALL IDLE SPROCKET ASSEMBLY
  1. Apply a light coat of engine oil to rotating surface of the idle gear shaft No. 1.



    A076299E02
  1. Temporarily install the idle gear shaft No. 1 together with the idle gear shaft No. 2 while aligning the knock pin of the idle gear shaft No. 1 with the knock pin groove of the cylinder block.

    NOTICE:
    Be careful of the idle gear direction.

  1. Using 10 mm hexagon wrench, tighten the idle gear shaft No. 2.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. Remove the bar from the chain tensioner.



6. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A076300E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

  1. Apply MP grease to the oil seal lip.



7. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material. Be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.



    G036305E01
  1. Install a new O-ring onto the LH cylinder head as shown in the illustration.



    G036306E01
  1. Apply continuous beads of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the 4 locations shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent



    A076303E04
  1. Apply continuous beads of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the timing chain cover as shown in the illustration.

    Seal packing:
    Water pump part:
    Part No. 08826-00100 or equivalent
    Other parts:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. Install the timing chain cover within 3 minutes of applying the seal packing. Timing chain cover bolts and nuts must be tightened within 15 minutes of installation. Otherwise, the seal packing must be removed and reapplied.
    2. Do not apply seal packing to portion A shown in the illustration.



    A076304E02
  1. Align the key way of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear, and slide the timing chain cover into place.



    G036303E02
  1. Install the timing chain cover with the 24 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Pay attention not to wrap the chain and slipper over the timing chain cover seal line.

    Each bolt length is as follows:
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    55 mm (2.17 in.)



8. INSTALL VVT SENSOR
  1. LH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.

    4. Connect the water by-pass hoses No. 4 and No. 5.

  1. RH bank side VVT sensor:

    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

    2. Install the VVT sensor with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Connect the VVT sensor connector.



9. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Install the 2 camshaft timing oil control valves with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 connectors.



10. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076311E02
  1. Install the cylinder head cover within 3 minutes of applying seal packing. Tighten the cylinder head cover bolts and nuts within 15 minutes of installing the cylinder head cover. Otherwise, the seal packing mush be removed and reapplied.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the cylinder head cover within 3 minutes after applying the seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

  1. Install the seal washers onto the bolts.



    A076503E03
  1. Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut

    HINT:
    Each bolt length is as follows.
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    60 mm (2.36 in.)



11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076310E02
  1. Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the cylinder head cover within 3 minutes of applying the seal packing. Tighten the cylinder head cover bolts and nuts within 15 minutes of installing the cylinder head cover. Otherwise, the seal packing must be removed and reapplied.

  1. Install the seal washers onto the bolts.



    A072943E03
  1. Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut

    HINT:
    Each bolt length is as follows.
    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    60 mm (2.36 in.)



12. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

  1. Connect the 6 ignition coil connectors.



13. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket onto the intake air surge tank.

  1. Using the socket hexagon wrench 8, install the intake air surge tank with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Install the 2 intake air surge tank nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Install the 2 surge tank stays with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the oil baffle plate with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the clutch flexible hose bracket with the nut (w/ Manual Transmission).

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. Install the 3 wire harness clamps and hose clamp.

  1. Connect the throttle body w/ motor connector.

  1. Connect the 2 VSV connectors.

  1. Connect the ventilation hose.

  1. Connect the fuel vapor feed hose.

  1. Connect the 2 water by-pass hoses.



14. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.



    A076452E01
  1. Install a new O-ring onto the oil pump.



    G036801E01
  1. Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the oil pan as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the oil pan within 3 minutes of applying the seal packing. Tighten the oil pan bolts and nuts within 15 minutes of installing the oil pan. Otherwise, the seal packing must be removed and reapplied.



    G036833E01
  1. Install the oil pan with the 17 bolts and 2 nuts, and tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf } for 10 mm (0.39 in.) head
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } for 12 mm (0.47 in.) head

    HINT:
    Each bolt length is as follows:

    Bolt
    Length
    A
    25 mm (0.98 in.)
    B
    45 mm (1.77 in.)
    C
    14 mm (0.55 in.)



    A076446E01
  1. Install the 4 housing bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the flywheel housing under cover.



15. INSTALL OIL STRAINER SUB-ASSEMBLY


A072951E01
  1. Install a new gasket and the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



16. INSTALL NO.2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil pan and oil pan No. 2.



    A076308E02
  1. Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) as shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    Install the oil pan No. 2 within 3 minutes of applying the seal packing. Tighten the oil pan No. 2 bolts and nuts within 15 minutes of installing the oil pan No. 2. Otherwise, the seal packing must be removed and reapplied.



    A072949E01
  1. Install the oil pan No. 2 with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolts
    10 N*m{ 102 kgf*cm , 7.4 in.*lbf } for nut



17. INSTALL CRANKSHAFT PULLEY


A076309E02
  1. Using SST, install the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    250 N*m{ 2,549 kgf*cm , 184 ft.*lbf }



18. INSTALL NO.1 IDLER PULLEY SUB-ASSEMBLY


A076438E01
  1. Install the idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    DOUBLE is marked on the idler pulley No. 1 to distinguish it from the idler pulley No. 2.



19. INSTALL NO.2 IDLER PULLEY SUB-ASSEMBLY


A076338E01
  1. Install the 2 idler pulleys with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



20. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


A076445E03

NOTICE:
A bolt in position A is not reusable.

HINT:
Each bolt length is as follows:
Position
Length
A
70 mm (2.76 in.)
B, C, D and E
33 mm (1.30 in.)

  1. Use a new bolt in position A.

  1. Finger-tighten the bolts in positions A and E and install the bracket.

  1. Tighten the bolts in positions A and E.

    Torque:
    36 N*m{ 267 kgf*cm , 27 ft.*lbf }

  1. Tighten the bolts in positions B, C and D.

    Torque:
    36 N*m{ 267 kgf*cm , 27 ft.*lbf }



21. INSTALL COOLER COMPRESSOR ASSEMBLY
  1. Install the cooler compressor assembly with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the cooler compressor assembly connector.

  1. Install the suction hose sub-assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



22. INSTALL GENERATOR ASSEMBLY
  1. Install the generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the wire harness clamp bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the wire harness.

    1. Connect the wire harness to terminal B and install the nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 7.0 ft.*lbf }

    2. Connect the connector to the generator assembly.

    3. Install the wire harness stay with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



23. INSTALL VANE PUMP ASSEMBLY


A076444E02
  1. Install the vane pump with the 2 bolts.

  1. Connect the power steering pressure switch connector.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    NOTICE:
    Do not hit the pulley with other parts when installing the vane pump.

  1. Connect the power steering pressure switch connector.



24. INSTALL WATER INLET
  1. Install a new gasket onto the water inlet with thermostat.

  1. Install the water inlet with thermostat with the 3 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



25. INSTALL OIL LEVEL GAGE GUIDE


A076314E02
  1. Install a new O-ring onto the oil level gauge guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the oil level gauge guide end into the guide hole of the oil pan.

  1. Install the oil level gauge guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the oil level gauge guide.



26. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the ventilation hose No. 2.



27. INSTALL FAN SHROUD


G036144E01
  1. Provisionally install the fan shroud together with the fan pulley.

  1. Install the fan and generator V belt .

  1. Install the fan pulley with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the 2 cooler hoses into the clamp (with automatic transmission).

  1. Connect the hose to the radiator reserve tank.



28. INSTALL RADIATOR SUPPORT TO FRAME SEAL LH


29. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
(Click here)


30. INSTALL POWER STEERING LINK ASSEMBLY
(Click here)


31. INSTALL BATTERY


32. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Capacity:
    2WD:
    Drain and refill with oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Drain and refill without oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Dry fill
    5.6 liters (5.9 US qts, 4.9 lmp. qts)
    PRE RUNNER and 4WD:
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.



33. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:

    Transmission
    Capacity
    Manual Transmission
    9.7 liters (10.3 Us qts, 8.5 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.



34. ADD DIFFERENTIAL OIL (for 4WD)


35. INSPECT DIFFERENTIAL OIL (for 4WD)


D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Differential carrier assembly front:
    1.45 to 1.55 litters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)

    Rear differential carrier assembly:
    2WD: 3.26 to 3.36 litters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Pre, 4WD: 2.75 to 2.85 litters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



36. ADD POWER STEERING FLUID


37. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).

    2. Repeat step A several times.

  1. Stop the engine.



    C114971E01
  1. Check for foaming or emulsification.
    Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.

  1. Check the fluid level.



38. CHECK FOR ENGINE OIL LEAKAGE


39. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



40. CHECK FOR POWER STEERING FLUID LEAKAGE


41. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


42. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



43. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.



    G035612E02
  1. When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Select the following menu items: DIAGNOSIS / ENHANCED OBD ll / DATA LIST / IGN ADVANCE.

    3. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A118802E01
  1. When not using intelligent tester.

    1. Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to connect the terminals wrongly. It causes breakage of the engine.

    2. Remove the air cleaner.



    3. A076315E02
    4. Pull out the wire harness as shown in the illustration.

    5. Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects the first signal.
      1. After checking, be sure to wrap the wire harness with tape.



    6. A076316E01
    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12°CA BTDC during idling (Transmission in neutral position)

    8. Remove the SST from the DLC3.

    9. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24°CA BTDC during idling (Transmission in neutral position)

    10. Install the air cleaner.