Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › TIMING CHAIN (for 4WD and Pre-Runner)

TIMING CHAIN (for 4WD and Pre-Runner) > REMOVAL

for Preparation Click here



1. REMOVE BATTERY


2. DRAIN ENGINE COOLANT


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



3. DRAIN ENGINE OIL
  1. Fill with fresh engine oil.

    Capacity:
    2WD:
    Drain and refill with oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Drain and refill without oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Dry fill
    5.6 liters (5.9 US qts, 4.9 lmp. qts)
    PRE RUNNER and 4WD:
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.



4. REMOVE POWER STEERING LINK ASSEMBLY
(Click here)


5. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
(Click here)


6. REMOVE V-BANK COVER


A075593E01
  1. Remove the 2 nuts, then remove the V-bank cover.



7. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G036137E02
  1. Disengage the 9 clips, then remove the radiator support to frame seal.



8. REMOVE FAN SHROUD


G036138E01
  1. Disconnect the hose from the radiator reserve tank.



    G036139E01
  1. Remove the 2 cooler hoses from the clamp (with automatic transmission).

  1. Remove the 4 nuts from the fan pulley.

  1. Remove the fan and generator V belt .

  1. Remove the 2 bolts from the fan shroud.

  1. Remove the fan pulley and fan shroud.



9. REMOVE AIR CLEANER ASSEMBLY


A075594E01
  1. Disconnect the ventilation hose No. 2.



    A075595E01
  1. Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Remove the 2 wire harness clamps.



    A075596E01
  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts, then remove the air cleaner.



10. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and pull out the oil level gauge guide.

  1. Remove the O-ring from the oil level gauge guide.



11. REMOVE WATER INLET


A076319E02
  1. Remove the 3 nuts, then remove the water inlet with thermostat and gasket.



12. SEPARATE VANE PUMP ASSEMBLY


A076444E02
  1. Disconnect the power steering pressure switch connector.

  1. Remove the 2 bolts, then separate the vane pump.

    NOTICE:
    Do not hit the pulley with other parts when separating the vane pump.

    HINT:
    The vane pump is suspended securely.



13. REMOVE GENERATOR ASSEMBLY


A076407E01
  1. Disconnect the wire harness.

    1. Remove the bolt and wire harness stay.

    2. Disconnect the connector from the generator assembly.

    3. Remove the terminal cap and nut.

    4. Disconnect the wire harness from terminal B.



    A076408E01
  1. Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.



    A076409E01
  1. Remove the 2 bolts, then remove the generator assembly.



14. SEPARATE COOLER COMPRESSOR ASSEMBLY


G036154E01
  1. Remove the bolt, then separate the suction hose sub-assembly.



    G036155E01
  1. Disconnect the cooler compressor assembly connector.

  1. Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.



15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A076445E01
  1. Remove the 5 bolts, then remove the V-ribbed belt tensioner.



16. REMOVE NO.2 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the 2 bolts, then remove the idler pulley No. 2.



17. REMOVE NO.1 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the bolt, then remove the idler pulley No. 1.



18. REMOVE CRANKSHAFT PULLEY


A072947E02
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



19. REMOVE NO.2 OIL PAN SUB-ASSEMBLY


A072949E01
  1. Remove the 10 bolts and 2 nuts.



    A072950E02
  1. Insert the blade of SST between the oil pan and oil pan No. 2, cut off applied sealer and remove the oil pan No. 2.

    SST
    09032-00100  

    NOTICE:
    1. Be careful not to damage the contact surfaces of the oil pan and oil pan No. 2.
    2. Be careful not to damage the oil pan No. 2 flange.



20. REMOVE OIL STRAINER SUB-ASSEMBLY


A072951E01
  1. Remove the 2 nuts, then remove the oil strainer and gasket.



21. REMOVE OIL PAN SUB-ASSEMBLY


A076446E01
  1. Remove the 4 housing bolts.

  1. Remove the flywheel housing under cover.



    A072952E01
  1. Remove the 17 bolts and 2 nuts.



    G036806E01
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.



22. REMOVE INTAKE AIR SURGE TANK


A076500E02
  1. Disconnect the 2 water by-pass hoses.



    A075644E01
  1. Disconnect the fuel vapor feed hose.



    A075645E01
  1. Disconnect the ventilation hose.



    A075646E01
  1. Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.



    G036170E01
  1. Remove the nut, then separate the clutch flexible hose bracket from the surge tank stay (with Manual Transmission).



    A076501E01
  1. Remove the 2 bolts and throttle body bracket.



    A076502E01
  1. Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.



    A075648E02
  1. Remove the 2 nuts.

  1. Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and gasket.



23. REMOVE IGNITION COIL ASSEMBLY


G036133E01
  1. Disconnect the 6 connectors.

  1. Remove the 6 bolts, then remove the 6 ignition coils.



24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


A076503E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



26. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


G036118E01
  1. Disconnect the 2 connectors.

  1. Remove the 2 bolts, then remove the 2 camshaft timing oil control valves.



27. REMOVE VVT SENSOR


A076413E01
  1. RH bank side VVT sensor:

    1. Disconnect the VVT sensor connector.

    2. Remove the bolt and VVT sensor.



    A076414E01
  1. LH bank side VVT sensor:

    1. Disconnect the water by-pass hoses No. 4 and No. 5 .

    2. Disconnect the VVT sensor connector.



    3. A076415E01
    4. Remove the bolt and VVT sensor.



28. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


G036303E01
  1. Remove the 24 bolts and 2 nuts.



    G036304E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.



29. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A072957E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump assembly. Wrap a tip of the screwdriver with tape.



30. SET NO.1 COMPRESSION TO TDC/COMPRESSION


A076450E01
  1. Using the crankshaft pulley set bolt, turn the crankshaft to align the crankshaft set key with the timing line of the cylinder block.



    G036290E03
  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.



31. REMOVE NO.1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A072958E02
  1. While turning the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner down ward, insert a bar of φ 3.5 mm (0.138) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts, then remove the chain tensioner.



32. REMOVE CHAIN TENSIONER SLIPPER


33. REMOVE IDLE SPROCKET ASSEMBLY


A072959E01
  1. Using a 10 mm hexagon wrench, remove the idle gear shaft No. 2, idle gear No. 1 and idle gear shaft No. 1.



34. REMOVE NO.2 CHAIN VIBRATION DAMPER
  1. Remove the 2 chain vibration dampers No. 2.



35. REMOVE CHAIN SUB-ASSEMBLY