Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › TIMING CHAIN

TIMING CHAIN > REMOVAL

for Preparation Click here



1. REMOVE HOOD SUB-ASSEMBLY


2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD and Pre-Runner)
  1. Remove the 4 bolts, then remove the No. 1 engine under cover.



4. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD and Pre-Runner, Regular Cab)
  1. Remove the 4 bolts, then remove the No. 2 engine under cover.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Install a new gasket, then install the oil pan drain plug.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



6. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the 4 bolts, then remove the engine under cover No. 1. (PRE RUNNER AND 4WD TYPE)



    G038197E01
  1. Install a vinyl hose onto the radiator side.



    G038198E01
  1. Install a vinyl hose onto the engine side.



    G038199E01
  1. Loosen the engine drain plug.

  1. Loosen the radiator drain plug.

  1. Remove the radiator cap and drain coolant.

  1. Drain the coolant from the reservoir tank.



7. REMOVE BATTERY


8. REMOVE BATTERY TRAY


9. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G038206E01
  1. Disengage the 9 clips, then remove the radiator support to frame seal LH.



10. REMOVE FAN SHROUD


A086838E01
  1. Loosen the 4 nuts shown in the illustration.

  1. Remove the fan and generator V belt.



    G038207E01
  1. Disconnect the radiator reserve tank hose from the radiator.



    G038208E01
  1. Disconnect the oil cooler inlet and outlet hoses from the fan shroud. (for Automatic Transmission)



    G038209E01
  1. Remove the 2 bolts shown in the illustration.



    G038210E01
  1. Remove the 4 nuts, then remove the fan shroud and fan with fluid coupling together.

    NOTICE:
    Make sure that the fan shroud and fan with fluid coupling do not make any contact with the radiator when they are removed.



    G038211E01
  1. Remove the fan pulley.



11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


G037934E01
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the wire harness clamp.

  1. Loosen the hose clamp bolt, then disconnect the air cleaner hose No. 1.

  1. Disconnect the 2 air cleaner clamps.

  1. Remove the air cleaner cap together with the air cleaner hose No. 1.



12. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


13. REMOVE AIR CLEANER CASE
  1. Remove the 3 bolts, then remove the air cleaner case.



14. SEPARATE VANE PUMP ASSEMBLY


G037555E01
  1. Disconnect the vane pump connector.

  1. Remove the 2 bolts, then separate the vane pump.

    HINT:
    Do not disconnect the hose. Hang the vane pump with a rope.



15. REMOVE NO. 2 RADIATOR HOSE


16. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)


G038205E01
  1. Remove the bolt shown in the illustration.



    G038234E01
  1. Disconnect the compressor and magnetic clutch connector.

  1. Remove the 4 bolts, then separate the compressor and magnetic clutch.

    HINT:
    Do not disconnect the hose. Hang the vane pump with a rope.



17. REMOVE RADIATOR HOSE INLET


18. SEPARATE WATER HOSE SUB-ASSEMBLY


G038551E01
  1. Separate the water hoses.



19. DISCONNECT FUEL HOSE


G037900E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



20. DISCONNECT FUEL HOSE NO.2


G037902E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



21. SEPARATE FUEL VAPOR FEED HOSE ASSEMBLY


G038552E01
  1. Disconnect the fuel vapor feed hose.



22. DISCONNECT NO. 1 AIR INJECTION HOSE


G038553E01
  1. Disconnect the No.1 air injection hose.



23. DISCONNECT ENGINE WIRE
  1. Disconnect the connector from the ECM, then pull the engine wire harness to the compartment side.

    NOTICE:
    Do not forcibly pull the wire harness to the engine compartment side.

  1. Disconnect all wire harnesses and connectors in the engine room.



24. REMOVE EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 nuts.

  1. Remove the exhaust pipe tail from the 4 exhaust pipe supports.

  1. Remove the gasket from the exhaust pipe front.



25. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the exhaust pipe front from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold.



26. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
Transmission
See page
R155
Click here
R155F
Click here


27. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


28. REMOVE ENGINE ASSEMBLY


G037564E03
  1. Install the engine hanger with the bolt.

    Torque:
    42 N*m{ 420 kgf*cm , 30 ft.*lbf }

    Part No:
    Part Name
    Part No.
    Engine hanger
    12281-75040
    Bolt
    91552-A1020

    NOTICE:
    Be sure to use the bolts when installing the engine hanger.



    G038554E01
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Remove the 4 bolts and 4 nuts.

  1. Lift the engine out of the vehicle slowly and carefully by operating the engine sling device and chain block.

    NOTICE:
    Make sure that no wires, hoses or cables are connected to the engine.



29. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


30. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


31. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


G038108E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E03
  1. Remove the 10 bolts, then remove the flywheel.



32. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


    G038108E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A099868E05
  1. Remove the 10 bolts, drive plate spacer rear, drive plate and ring gear and drive plate spacer front.



33. REMOVE REAR END PLATE
  1. Remove the 2 bolts, then remove the rear end plate.



34. REMOVE INTAKE AIR CONNECTOR


G037694E01
  1. Disconnect the pressure sensor connector.

  1. Disengage the wire harness clamp.

  1. Disconnect the vacuum hose.



    G037695E01
  1. Disconnect the No. 2 ventilation hose.



    G037696E01
  1. Disconnect the vacuum hose.



    G037697E01
  1. Loosen the 2 hose clamp bolts.

  1. Remove the 3 bolts, then remove the intake air connector.



35. REMOVE GENERATOR ASSEMBLY


G038188E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the generator wire.

  1. Disconnect the generator connector.



    G038189E01
  1. Remove the 2 bolts, then remove the generator.



36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    G038212E01
  1. Remove the 3 bolts, then remove the V-ribbed belt tensioner.



37. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


A099635E01
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



38. REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)


G037912E02
  1. Remove the 5 bolts, then remove the idle pulley with bracket.



39. REMOVE CRANKSHAFT POSITION SENSOR


G037910E01
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt, then remove the camshaft position sensor.



40. REMOVE CAMSHAFT POSITION SENSOR


G037910E01
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt, then remove the camshaft position sensor.



41. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET


G037711E01
  1. Install a new gasket onto the intake manifold.

  1. Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037710E01
  1. Connect the engine wire harness to the relay block.

  1. Install the nut shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 connectors.



    G037709E01
  1. Install the harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Engage the wire harness clamp.

  1. Connect the compressor magnetic clutch connector. (w/ AIR CONDITIONING)

  1. Engage the engine wire harness clamp.

  1. Connect the VSV connector.



    G039455E01
  1. Connect the ventilation hose No. 3.



    G039454E01
  1. Connect the water by-pass hose No. 2.



    G037706E01
  1. Install the clamp bracket with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 in.*lbf }



    G037705E01
  1. Connect the vacuum hose.



    G037704E01
  1. Connect the fuel vapor feed hose to the VSV.



42. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


G038214E01
  1. Disconnect the ignition coil connectors.

  1. Disconnect the throttle with motor body connector.

  1. Disconnect the VSV connector.

  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the engine wire harness clamps.



    G038215E01
  1. Remove the bolts, then remove the ignition coils.



    G038216E01
  1. Disconnect the ventilation hose.



    A088646E03
  1. Remove the 19 bolts and 2 nuts, then remove the cylinder head cover.



43. REMOVE CRANKSHAFT PULLEY


A097861E06
  1. Set the No. 1 cylinder to the TDC/ compression.

    1. Turn the crankshaft pulley clockwise and align its timing mark notch with the timing mark "0".

    2. Check that the timing marks of the camshaft timing gear are located as illustrated.

      HINT:
      If not, turn the crankshaft to align the marks.



    G037559E01
  1. Using SST, loosen the crankshaft pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    HINT:
    Loosen the crankshaft pulley bolt until only 2 or 3 threads are still installed in the crankshaft.



    G035121E03
  1. Using SST, remove the crankshaft pulley and crankshaft pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



44. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY


45. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


G037265E01
  1. Remove the 18 bolts and 2 nuts.



    A099215E03
  1. Insert the blade of SST between the pans. Cut through the applied sealer and remove the oil pan.

    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surface of the oil pans.



46. REMOVE OIL STRAINER SUB-ASSEMBLY


G037268E01
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.



47. REMOVE OIL PAN SUB-ASSEMBLY


A086858E01
  1. Remove the 16 bolts and 2 nuts.



    G037270E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



48. REMOVE TIMING CHAIN COVER


G038244E01
  1. Remove the 2 nuts, then separate the water by-pass pipe No. 1.



    G037272E03
  1. Remove the 19 bolts and 2 nuts shown in the illustration.

    HINT:
    If the vehicle is equipped with air conditioning, bolts A are already removed since they are for installing the idle pulley with bracket.



    G037273E02
  1. Remove the oil pump by prying between the oil pump and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.



    G038245E01
  1. Remove the 4 O-rings.



    G036021E01
  1. Using a 10 mm socket hexagon wrench, remove the head straight screw plug.



49. REMOVE TIMING CHAIN GUIDE


G037546E01
  1. Make sure that each matchmark is in the position shown in the illustration.



    G037278E05
  1. Remove the 2 bolts, timing chain guide and O-ring.



50. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


A097899E04

NOTICE:
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a 3.0 mm (0.118 in.) diameter bar into the stopper plate hole.



    G037279E01
  1. Remove the bolt, nut, chain tensioner and gasket.



51. REMOVE CHAIN TENSIONER SLIPPER


G037281E03
  1. Remove the bolt and tensioner slipper.



52. REMOVE NO. 1 CHAIN VIBRATION DAMPER


G037280E04
  1. Remove the 2 bolts and vibration damper.



53. REMOVE CHAIN SUB-ASSEMBLY


54. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET


G037282E01
  1. Remove the crankshaft timing gear from the crankshaft.



55. REMOVE NO. 2 CHAIN VIBRATION DAMPER


G037295E03
  1. Remove the bolt and No. 2chain vibration damper.



56. REMOVE NO. 3 CHAIN VIBRATION DAMPER


G037296E01
  1. Remove the 2 bolts and No. 3chain vibration damper.



57. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


G039451E01
  1. Remove the nut and No. 2 chain tensioner assembly.



58. REMOVE NO.2 CHAIN SUB-ASSEMBLY


G037298E02
  1. Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.

  1. Remove the crankshaft timing sprocket No. 2 and chain.