Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1258/58    Transfer 4WD Position Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit monitors whether the transfer is in 2WD or 4WD mode and inputs the signal to the skid control ECU. In 2WD mode, TRAC is activated.
In 4WD mode, A-TRAC is activated.

DTC No.
DTC Detecting Conditions
Trouble Areas
C1258/58
  1. 4WD:
    Open in 4WD detecting circuit
  2. 2WD:
    Terminal NEO ground short, or abnormal signals transmitted to terminal EXI
  1. Transfer indicator switch (4WD position)
  2. Transfer indicator switch (4WD position) circuit
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM


C124777E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.CONFIRM VEHICLE TYPE
  1. Confirm the vehicle drive train.

    Drive Train
    Proceed to
    4WD
    A
    2WD, Pre-Runner
    B



B
Go to step 7
A


2.INSPECT SKID CONTROL ECU (EXI TERMINAL VOLTAGE)


    C121700E16
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard:
    Tester Connection
    Transfer Condition
    Specified Condition
    S1-27 (EXI) - Body ground
    2WD
    8 to 16 V
    S1-27 (EXI) - Body ground
    4WD
    Below 1.5 V

  1. Turn the ignition switch to OFF.

  1. Reconnect the skid control ECU connector.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



NG
END
A

REPLACE MASTER CYLINDER SOLENOID 

4.INSPECT TRANSFER INDICATOR SWITCH (4WD POSITION)


    F052057E02
  1. Disconnect the transfer indicator switch (4WD position) connector.

  1. Remove the transfer indicator switch (4WD position).

  1. Measure the voltage.

    Standard:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Free
    10 kΩ or higher

  1. Reinstall the transfer indicator switch (4WD position).

  1. Reconnect the transfer indicator switch (4WD position) connector.



NG
REPLACE TRANSFER INDICATOR SWITCH (4WD POSITION)
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)


    F052062E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard (1GR-FE):
    Tester Connection
    Specified Condition
    S1-27 (EXI) - B6-8 (4WD)
    Below 1 Ω

    Standard (2TR-FE):
    Tester Connection
    Specified Condition
    S1-27 (EXI) - B5-21 (4WD)
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)


    F052382E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the 4WD control ECU connector.

  1. Measure the resistance.

    Standard :
    Tester Connection
    Specified Condition
    S1-27 (EXI) - F13-26 (ADD)
    Below 1 Ω

  1. Reconnect the 4WD control ECU connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

END 

7.CHECK HARNESS AND CONNECTOR (NEO TERMINAL - BODY GROUND)


    C121700E17
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Vehicle Drive Train
    Specified Condition
    S1-10 (NEO) - Body ground
    2WD, Pre-runner
    10 kΩ or higher
    S1-10 (NEO) - Body ground
    4WD
    Below 1 Ω

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID