TIRE PRESSURE WARNING SYSTEM > DTC CHECK / CLEAR |
| CHECK DTC (USING SST CHECK WIRE) |
Check DTCs.
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() ![]() |
Read and record any DTCs indicated by the tire pressure warning light in the combination meter. Refer to the illustration for examples of the normal system code and DTCs 13 and 33.
| Trouble Area | See Procedure |
| Tire pressure warning light circuit |
Click here
|
| TC and CG terminal circuit |
Click here
|
Refer to the Diagnostic Trouble Code Chart (Click here ) for DTC information.
After completing the check, turn the ignition switch off and remove the SST from the DLC3.
| CHECK DTC (USING INTELLIGENT TESTER) |
![]() |
Check DTCs.
Connect the intelligent tester with CAN VIM to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Read the DTCs by following the prompts on the tester screen.
| CLEAR DTC |
Connect the intelligent tester with CAN VIM to the DLC3.
Turn the ignition switch to the ON position.
Clear the DTCs by following the prompts on the tester screen.
| IDENTIFY TIRE PRESSURE WARNING VALVE AND TRANSMITTER CORRESPONDING TO DTC |
Set the tire pressures to the appropriate specified values.
| Tire Size | Front Wheel kPa (kgf/cm2, psi) | Rear Wheel kPa (kgf/cm2, psi) | Spare Wheel kPa (kgf/cm2, psi) |
| P215/70 R15 | 200 (2.0, 29) | 220 (2.2, 32) | 220 (2.2, 32) |
| P255/45 R18 | 240 (2.4, 34) | 240 (2.4, 34) | 240 (2.4, 34) |
| P245/75 R16 | 200 (2.0, 29) | 200 (2.0, 29) | 200 (2.0, 29) |
| P265/70 R16 (OPR)* | 200 (2.0, 29) | 220 (2.2, 32) | 220 (2.2, 32) |
| P265/65 R17 | 200 (2.0, 29) | 200 (2.0, 29) | 200 (2.0, 29) |
![]() |
Jack up the vehicle.
Select TIREPRESS by following the prompts displayed on the intelligent tester.
| Item | Measurement Item/ Range (Display) |
| TIREPRESS1 | ID1 tire inflation pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi) |
| TIREPRESS2 | ID2 tire inflation pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi) |
| TIREPRESS3 | ID3 tire inflation pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi) |
| TIREPRESS4 | ID4 tire inflation pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi) |
| TIREPRESS5 | ID5 tire inflation pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi) |
Rapidly release the tire pressure from any tire to 40 kPa (0.4 kgf/cm2, 5.8 psi)/ 30 seconds or more.
Check the DATA LIST.
| Display | Detection Condition |
| One of TIREPRESS data (ID1 to ID5) changes | Normal |
| None of TIREPRESS data change | Transmitter corresponding to DTC |
Repeat this procedure to identify the malfunctioning tire pressure warning valve and transmitter.