Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



ENTER TEST MODE

HINT:
  1. The operation of the tire pressure warning reset switch can be checked in TEST MODE.
  2. During TEST MODE, the system cannot be initialized by pressing the tire pressure warning reset switch. The tire pressure warning reset switch circuit can be inspected in this mode.



    C122893E01
  1. Make sure that the ignition switch is off.

  2. Connect the intelligent tester with CAN VIM to the DLC3.

  3. Turn the ignition switch to the ON position and turn the tester ON.



  4. C122887E01
  5. Select TEST MODE on the intelligent tester.



  6. C110635E03
  7. Confirm that the tire pressure warning light in the combination meter blinks at 0.125 second intervals (4Hz).

    HINT:
    1. When starting the signal checks, the tire pressure warning ECU sets all the signal check DTCs first.
      After the signal checks for each inspection item have been completed, the DTCs of the items that are determined to be normal by the tire pressure warning ECU are cleared.
      The DTCs for other inspection items may not be cleared when only a certain signal is inspected.
    2. When the mode returns from signal check mode to normal mode, all the signal check DTCs are cleared.

    TEST MODE CODE 
    SIGNAL CHECK DTC
    Test Signal
    SIGNAL CHECK DTC Clear Condition
    C2181/81 to C2185/85
    Transmitter Data
    Data received from the tire pressure warning valve and transmitter which has transmitter ID registered in tire pressure warning ECU
    C2191/91
    Vehicle Speed Signal
    Vehicle speed of 12 mph (20 km/h) or more detected for 3 seconds or more
    -
    Tire Pressure Reset Switch
    -


PERFORM SIGNAL CHECK


    C122893E01
  1. Make sure that the ignition switch is off.

  2. Connect the intelligent tester with CAN VIM to the DLC3.

  3. Turn the ignition switch to the ON position and turn the tester ON.



  4. Select the SIGNAL CHECK on the intelligent tester.


    C122891E01



  5. Check the transmission data (for DTCs from C2181/81 to C2185/85)

    1. Set the tire pressures to the appropriate specified values.

      Tire Size
      Front Wheel
      kPa (kgf/cm2, psi)
      Rear Wheel
      kPa (kgf/cm2, psi)
      Spare Wheel
      kPa (kgf/cm2, psi)
      P215/70 R15
      200 (2.0, 29)
      220 (2.2, 32)
      220 (2.2, 32)
      P255/45 R18
      240 (2.4, 34)
      240 (2.4, 34)
      240 (2.4, 34)
      P245/75 R16
      200 (2.0, 29)
      200 (2.0, 29)
      200 (2.0, 29)
      P265/70 R16 (OPR)*
      200 (2.0, 29)
      220 (2.2, 32)
      220 (2.2, 32)
      P265/65 R17
      200 (2.0, 29)
      200 (2.0, 29)
      200 (2.0, 29)
      *: Used on Off Road Package Models



    2. C124984E01
    3. Jack up the vehicle.

    4. Rapidly release the tire pressure of all the tires to 40 kPa (0.4 kgf/cm2, 5.8 psi)/ 30 seconds or more one by one.

      HINT:
      1. It may take up to 1 minute to update the tire pressure data.
      2. The tire pressure warning light that is blinking at 0.125 second intervals will come on for 1 second when the tire pressure warning ECU receives the transmission data.
      3. If the transmission data have not been received, reset the tire pressures to the appropriate specified values and rotate the tires 90 to 270 degrees. Then recheck for the transmission data again.

  6. Check the vehicle speed signal (for DTC C2191/91)

    1. Drive the vehicle at 12 mph (20 km/h) or more for 10 seconds or more.

      HINT:
      The tire pressure warning light that is blinking at 0.125 second intervals will come on for 1 second when the tire pressure warning ECU receives the transmission data.

  7. Check the tire pressure warning reset switch

    HINT:
    Since there is no test mode code for the reset switch, check the reset switch by observing the status of the tire pressure warning light.


    1. Press the tire pressure warning reset switch.

    2. Check the tire pressure warning light blinking pattern.

      Result:

      Test Signal
      Normal Condition
      Tire Pressure Warning Reset Switch
      1. Switch ON: Tire pressure warning light comes on
      2. Switch OFF: Tire pressure warning light blinks (4Hz)

  8. Read the test mode code.

    1. After the signal check has been completed, check for signal check DTCs to confirm the system status (Click here ).

  9. Clear the DTCs.

    HINT:
    When the mode returns from signal check mode to normal mode, all the signal check DTCs are cleared.

  10. End SIGNAL CHECK
    After SIGNAL CHECK has finished, turn the ignition switch off and disconnect the tester.

    HINT:
    If a trouble code is displayed during the test mode DTC check, check the circuit indicated by the code. For details of each code, refer to the relevant page listed under respective "DTC No." in the table below.


    TEST MODE DTCs 
    DTC No.
    Detection Item
    Trouble Area
    C2181/81
    (Click here )
    Transmitter ID1 not received
    1. Tire pressure warning antenna and receiver
    2. Each tire pressure warning valve and transmitter
    3. Tire pressure warning ECU
    4. Wire harness or connector
    C2182/82
    (Click here )
    Transmitter ID2 not received
    1. Tire pressure warning antenna and receiver
    2. Each tire pressure warning valve and transmitter
    3. Tire pressure warning ECU
    4. Wire harness or connector
    C2183/83
    (Click here )
    Transmitter ID3 not received
    1. Tire pressure warning antenna and receiver
    2. Each tire pressure warning valve and transmitter
    3. Tire pressure warning ECU
    4. Wire harness or connector
    C2184/84
    (Click here )
    Transmitter ID4 not received
    1. Tire pressure warning antenna and receiver
    2. Each tire pressure warning valve and transmitter
    3. Tire pressure warning ECU
    4. Wire harness or connector
    C2185/85
    (Click here )
    Transmitter ID5 not received
    1. Tire pressure warning antenna and receiver
    2. Each tire pressure warning valve and transmitter
    3. Tire pressure warning ECU
    4. Wire harness or connector
    C2191/91
    (Click here )
    Vehicle speed signal error
    1. Vehicle speed sensor
    2. Combination meter
    3. Tire pressure warning ECU
    4. Wire harness or connector