Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

for Preparation Click here


DESCRIPTION

The ECM optimizes the valve timing by using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly.
This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviations in crankshaft and camshaft position sensor 1 signals (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Camshaft timing oil control valve assembly
  3. Camshaft timing gear assembly
  4. ECM
P0018
Deviations in crankshaft and camshaft position sensor 2 signals (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Camshaft timing oil control valve assembly
  3. Camshaft timing gear assembly
  4. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (bank 1) or P0018 (bank 2).
This DTC indicates that the intake camshaft has been installed toward the crankshaft at an incorrect angle, caused by factors such as the timing chain having jumped a tooth.
This monitor begins to run after the engine has idled for 5 minutes.

MONITOR STRATEGY


Related DTCs
P0016: Camshaft Timing Misalignment at idling
Required Sensors/Components (Main)
Camshaft timing gear assembly
Required Sensors/Components (Related)
VVT sensor
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 1 minute
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
P0010, P0020 (Camshaft timing oil control valve)
P0016, P0018 (VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0346, P0347, P0348 (VVT Sensor)
Engine speed
500 to 1000 rpm

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions is met
-
VVT learning value at maximum retarded valve timing (Bank 1)
Less than 22.5°CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (Bank 2)
Less than 22.5°CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (Bank 1)
More than 45.2°CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (Bank 2)
More than 45.2°CA (crankshaft angle)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A197314E13

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0016 or P0018.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
  16. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.
  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. The monitor for this DTC detects when the timing chain is shifted by one tooth or more.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0016 or P0018 is output
    A
    DTC P0016 or P0018 and other DTCs are output
    B

HINT:
If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / VVT Change Angle #1 or VVT Change Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 7

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


5.INSPECT OIL CONTROL VALVE FILTER


    A237948E01
  1. Remove the plug and filter, then remove the gasket from each cylinder head .

  1. Check that the filter is not clogged.
    Text in Illustration 
    *1
    Plug
    *2
    Oil Control Valve Filter

    OK:
    Filter is not clogged.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER
OK


6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (bank 1 or bank 2) (Click here or Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0016 or P0018 is output
    B



B
REPLACE ECM (Click here)
A

END