DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Open or short in camshaft oil control valve assembly (bank 1) circuit (1 trip detection logic) |
|
| P0020 | Open or short in camshaft oil control valve assembly (bank 2) circuit (1 trip detection logic) |
|
| Related DTCs | P0010: Camshaft oil control valve assembly (bank 1) range check P0020: Camshaft oil control valve assembly (bank 2) range check |
| Required Sensors/Components (Main) | Camshaft oil control valve assembly |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| All of the following conditions are met | - |
| Ignition switch | ON |
| Starter | OFF |
| Time after ignition switch off to ON | 0.5 seconds or more |
| One of the following conditions is met | A, B or C |
| A. All of the following conditions are met | - |
| a. Battery voltage | 11 V to 13 V |
| b. Target duty cycle | Less than 70% |
| c. Output duty cycle | 100% or more |
| B. All of the following conditions are met | - |
| a. Battery voltage | 13 V or more |
| b. Target duty cycle | Less than 80% |
| c. Output duty cycle | 100% or more |
| C. All of the following conditions are met | - |
| a. Current cut status | Not cut |
| b. Output duty cycle | 3% or less |
| VVT oil control valve duty ratio | More than 3%, and Less than 100% |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ OUTPUT DTC (DTC P0010 OR P0020) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTC after recording the freeze frame data and DTC.
Turn the ignition switch off.
Start the engine and allow the engine to idle.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0010 or P0020 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft timing oil control valve assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Disconnect the camshaft timing oil control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C4-1 - E10-19 (OC1+) | Always | Below 1 Ω |
| C4-2 - E10-20 (OC1-) | Always | Below 1 Ω |
| C3-1 - E9-19 (OC2+) | Always | Below 1 Ω |
| C3-2 - E9-20 (OC2-) | Always | Below 1 Ω |
| C4-1 or E10-19 (OC1+) - Body ground | Always | 10 kΩ or higher |
| C4-2 or E10-20 (OC1-) - Body ground | Always | 10 kΩ or higher |
| C3-1 or E9-19 (OC2+) - Body ground | Always | 10 kΩ or higher |
| C3-2 or E9-20 (OC2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||