Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0451
Canister pressure sensor noise
Sensor output voltage fluctuates frequently within certain time period.
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
  1. EVAP monitoring (ignition switch off)
  2. Engine running
2 trip
Canister pressure sensor signal becomes fixed/flat
Sensor output voltage does not vary within certain time period.
  1. EVAP monitoring (ignition switch off)
2 trip
P0452
Canister pressure sensor voltage low
Evap pressure less than 42.11 kPa(abs) [315.85 mmHg(abs)] for 0.5 seconds.
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip
P0453
Canister pressure sensor voltage high
Evap pressure more than 123.761 kPa(abs) [928.28 mmHg(abs)] for 0.5 seconds.
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip

HINT:
The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The circuit description can be found in the EVAP (Evaporative Emission) System .

MONITOR DESCRIPTION


A115543E88

  1. DTC P0451: Canister pressure sensor noise or fixed/flat
    If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as noise from the canister pressure sensor, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC.
    Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC (Both the malfunctions are detected by 2 trip detection logic).
  2. DTC P0452: Canister pressure sensor voltage low
    If the canister pressure sensor voltage output (pressure) is below 0.45 V: 42.11 kPa(abs) [315.85 mmHg(abs)], the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
  3. DTC P0453: Canister pressure sensor voltage high
    If the canister pressure sensor voltage output (pressure) is 4.9 V: 123.761 kPa(abs) [928.28 mmHg(abs)] or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components (Main)
Canister pump module
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle: P0451 sensor fixed/flat
Continuous: P0451 sensor noise, P0452 and P0453
Duration
Less than 15 seconds: P0451 sensor noise
Within 2 minutes: P0451 sensor fixed/flat
0.5 seconds: P0452 and P0453
MIL Operation
Immediate: P0452 and P0453
2 driving cycles: P0451
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
None

P0451: Noise Monitor 
Atmospheric pressure
70 to 110 kPa(abs) [525 to 825 mmHg(abs)]
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 50°C (40 to 122°F)
Canister pressure sensor malfunction (P0452, 0453)
Not detected
Either of following conditions met
A or B
A. Engine condition
Running
B. Time after key off
5 or 7 or 9.5 hours

P0451: Stuck Monitoring 
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 50°C (40 to 122°F)
Canister pressure sensor malfunction (P0452, 0453)
Not detected
Atmospheric pressure
70 to 110 kPa(abs) [525 to 825 mmHg(abs)]
Time after key off
5 or 7 or 9.5 hours

P0452 and P0453 
Battery voltage
8 V or more
Starter
OFF
Either of following conditions met
(a) or (b)
(a) Ignition switch
ON
(b) Soak timer
ON

TYPICAL MALFUNCTION THRESHOLDS


P0451: Canister Pressure Sensor Noise 
Frequency that EVAP pressure change is 0.3 kPa(gauge) [2.25 mmHg(gauge)] or more
10 times or more in 10 seconds

P0451: Canister Pressure Sensor Stuck Monitoring 
EVAP pressure change during reference pressure measurement
Less than 0.65 kPa(gauge) [4.87 mmHg(gauge)]

P0452: Canister Pressure Sensor Low Voltage 
EVAP pressure
Less than 42.11 kPa(abs) [315.85 mmHg(abs)]

P0453: Canister Pressure Sensor High Voltage 
EVAP pressure
More than 123.761 kPa(abs) [928.28 mmHg(abs)]

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 19 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Enter the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menu items: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
  8. After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All readiness.
  9. Input the DTC: P0451, P0452 or P0453.
  10. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  11. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A193216E08


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
  2. Do not disassemble the canister pump module.
  3. The Techstream is required to conduct the following diagnostic troubleshooting procedure.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.

  1. Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

    Result 
    Display (DTC Output)
    Test Result
    Suspected Trouble Areas
    Proceed to
    P0451
    -
    1. Canister pressure sensor
    C
    P0452
    Less than 42.11 kPa(abs) [315.85 mmHg(abs)]
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Short in ECM circuit
    A
    P0453
    More than 123.761 kPa(abs) [928.28 mmHg(abs)]
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Open in ECM circuit
    B



B
Go to step 4

C
GO TO EVAP SYSTEM
A


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    E10-1 (PPMP) - Body ground
    Always
    Below 10 Ω
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in canister pressure sensor circuit
    A
    10 kΩ or more
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in ECM circuit
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Result
    Suspected Trouble Area
    Proceed to
    E10-1 (PPMP) - Body ground
    Always
    10 kΩ or more
    Short in canister pressure sensor circuit
    A
    Below 10 Ω
    Short in wire harness/connector (ECM - canister pressure sensor)
    B



A
Go to step 5

B
Go to step 6

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
A116297E07
  1. Disconnect the canister connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Canister Pump Module)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L1-2 (SGND) - Body ground
    Always
    100 Ω or less

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L1-4 (VCC) - Body ground
    Ignition switch ON
    4.5 V and 5.5 V
    L1-3 (VOUT) - Body ground
    Ignition switch ON
    4.5 V and 5.5 V


Result 
Result
Suspected Trouble Area
Proceed to
Voltage and resistance within standard ranges
Open in canister pressure sensor circuit
A
Voltage and resistance outside standard ranges
Open in wire harness/connector (ECM - canister pressure sensor)
B


B
Go to step 6
A


5.REPLACE CANISTER PUMP MODULE


  1. Replace the canister pump module (Click here).


    A121766E08


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister Assembly
    *7
    Canister Filter
    -
    -
    *a
    Inspection Area
    (check for disconnection and/or cracks)
    -
    -

    NOTICE:
    1. When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace canister and canister pump module together (replace canister assembly).
    2. Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace canister and the canister pump module together (replace canister assembly).
    3. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



NEXT
Go to step 8

6.REPAIR OR REPLACE HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

HINT:
If the exhaust tail pipe has been removed, go to the next step before reinstalling it.



NEXT
Go to step 8

7.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Driving the vehicle in accordance with the driving confirmation driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0451, P0452 or P0453.

  1. Check the DTC judgment result.

    Result 
    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit


NEXT

END