DTC P0505 Idle Control System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0505 | Idling speed continues to vary greatly from target idling speed (2 trip detection logic) |
|

| Related DTCs | P0505: Idle Speed Control Function |
| Required Sensors/Components (Main) | Electronic Throttle Control System |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Continuous |
| Duration | 10 minutes |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (Camshaft timing oil control valve) P0011, P0021 (VVT system - advance) P0012, P0022 (VVT System - retard) P0016, P0018 (VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P0748, P0778 (Pressure control solenoid) P0973, P0974, P0976, P0977, P0985, P0986 (Shift solenoid) P219A, P219B (Air-fuel ratio imbalance) |
| Engine | Running |
| Either of the following conditions are met | 1 or 2 |
| 1. Both of the following conditions are met | - |
| Engine speed - Target engine speed | Less than -100 rpm, or more than 200 rpm (A/C ON or NSW ON) Less than -100 rpm, or more than 150 rpm (A/C OFF and NSW OFF) |
| Idle air control flow rate learning value | 1.3 L/sec or less, or 8.5 L/sec or more |
| 2. Both of the following conditions are met | A and B |
| A. Frequency that both of the following conditions are met | 5 times or more |
| Engine speed - Target engine speed | Less than -100 rpm, or more than 200 rpm (A/C ON or NSW ON) Less than -100 rpm, or more than 150 rpm (A/C OFF and NSW OFF) |
| Vehicle condition | Stop after vehicle was driven at 10 km/h (6.25 mph) or more |
| B. Either of the following condition is met | (a) or (b) |
| (a) Amount of change of IAC flow rate learning value | +1.9 L/sec. or less, or -1.9 L/sec. or more |
| (b) IAC flow rate learning value | 1.3 L/sec. or less, or 8.5 L/sec. or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC P0505 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE) |
Check the throttle valve condition.
|
| ||||
| OK | |
| 5.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||