Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

NOTICE:
In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    The speed is indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 750 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 10 to 40%: Idling
    2. 10 to 40%: Running without load (2000 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from mass air flow meter/
    Min.: 0 gm/sec, Max.: 655.35 gm/sec
    3.2 to 4.7 gm/sec: Idling
    13.1 to 18.9 gm/sec: 2000 rpm
    If the mass air flow volume is approximately 0.0 gm/sec:
    1. The mass air flow meter power source circuit is open or short.
    2. The VG circuit is open or short.
    If the mass air flow volume is 271.0 gm/sec or more:
    1. The E2G circuit is open.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (176 to 212°F): After warming up
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is higher than 135°C (275°F): the sensor circuit is shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    Equivalent to ambient air temperature
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is higher than 128°C (262°F): the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data.
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
    Coolant temperature when engine started
    Service data.
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
    Intake air temperature when engine started
    Service data.
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position/
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No.1 Volt %
    Absolute accelerator pedal position No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal released
    54 to 86%: Accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute accelerator pedal position No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: Accelerator pedal released
    66 to 98%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    Accelerator pedal position sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.2
    Accelerator pedal position sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.98 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 4.7 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Throttle Sensor Volt %
    Throttle valve opening percentage according to throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA1.
    Throttl Sensor #2 Volt %
    Throttle valve opening percentage according to throttle position sensor No. 2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Accelerator pedal released
    2. 92 to 100%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA2.
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idling
    ON or OFF
    1. ON: Accelerator pedal released
    2. OFF: Accelerator pedal fully depressed
    -
    Throttle Require Position
    Required throttle position/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*1
    Throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 50 to 80%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM.
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    -
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    -
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 1.4 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.98 V
    1.7 to 2.5 V
    ETCS service data
    Throttle Motor Current
    Throttle motor current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    ETCS service data
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling after engine warmed up
    ETCS service data
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (closed)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Ignition switch to ON and system normal
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data
    Throttle Position
    Throttle valve opening angle/
    Min.: 0 deg, Max.: 499.99 deg
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    ISC Flow
    Flow rate calculated using information from each sensor/
    Min.: 0 L/s, Max.: 79.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    ISC Position
    Requested opening amount calculated using ISC control/
    Min.: 0 deg, Max.: 499.99 deg
    -
    Check the value when the engine stalls, is difficult to start, or idles roughly
    This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
    ISC Feedback Value
    ISC feedback compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    ISC Learning Value
    ISC learned compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Electric Load Feedback Val
    Compensation flow rate according to electrical load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Air Conditioner FB Val
    Compensation flow rate according to air conditioner load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    PS Feedback Val
    Compensation flow rate according to power steering load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Low Revolution Control
    Low engine speed control operation state/
    ON or OFF
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    N Range Status
    Shift lever N status/
    ON or OFF
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Eng Stall Control FB Flow
    Intake air compensation flow rate/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Deposit Loss Flow
    Flow loss due to deposits/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    1. This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
    2. Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
    3. When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI and ETCS fuses), performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
      1. Start the engine cold and allow the engine to idle.
      2. After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
      3. Turn the ignition switch off and wait for 30 seconds.
      4. Start the engine again, and allow the engine to idle for 5 minutes.
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 μs, Max.: 65535 μs
    2000 to 4000 μs: idling
    -
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.047 ml
    0.005 to 0.015 ml: Idling
    Quantity of fuel injection volume for 10 times.
    Fuel Pump Speed Control
    Fuel pump speed control status:
    ON or OFF
    ON: Idling
    -
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    -
    Vacuum Pump
    Key-OFF EVAP system leak detection pump status/
    ON or OFF
    -
    -
    Current Fuel Type
    Status of the current fuel type
    Gasoline/petrol
    -
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM.
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -200%, Max.: 199.993%
    Idling: -40 to 0%
    Service data.
    Vapor Pressure Pump
    Vapor pressure/
    Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg)
    Near atmosphere pressure: Fuel cap removed
    Pressure inside fuel tank monitored by vapor pressure sensor.
    Vapor pressure (Calculated)
    Vapor pressure (calculated)/
    Min.: -720.896 kPa (-5407.17 mmHg), Max.: 720.874 kPa (5407.002 mmHg)
    Near atmosphere pressure: Fuel cap removed
    Pressure inside fuel tank monitored by vapor pressure sensor.
    EVAP System Vent Valve
    Key-OFF EVAP system vent valve status/
    ON or OFF
    -
    -
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    -
    Purge Cut VSV Duty
    Purge cut VSV duty/
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Air fuel ratio:
    Min.: 0, Max.: 1.99
    0.8 to 1.2: During idling
    -
    AF Lambda B1S1
    Short-term fuel trim associated (bank 1 sensor 1)/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2S1
    Short-term fuel trim associated (bank 2 sensor 1)/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    Air fuel ratio sensor output voltage (bank 1 sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Voltage B2S1
    Air fuel ratio sensor output voltage (bank 2 sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Current B1S1
    Air fuel ratio sensor current (bank 1 sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    AFS Current B2S1
    Air fuel ratio sensor current (bank 2 sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    A/F Heater Duty #1
    Air fuel ratio heater duty ratio (bank 1)
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    A/F Heater Duty #2
    Air fuel ratio heater duty ratio (bank 2)
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    O2S B1S2
    Heated oxygen sensor output voltage (bank 1 sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S B2S2
    Heated oxygen sensor output voltage (bank 2 sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S Impedance B1S2
    Heated oxygen sensor impedance (bank 1 sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    After driving for approx. 10 min. in an urban area.
    O2S Impedance B2S2
    Heated oxygen sensor impedance (bank 2 sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    After driving for approx. 10 min. in an urban area.
    O2 Heater B1S2
    Heated oxygen sensor heater (bank 1 sensor 2)/
    Not Act or Active
    -
    -
    O2 Heater B2S2
    Heated oxygen sensor heater (bank 2 sensor 2)/
    Not Act or Active
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor current (bank 1 sensor 2)/
    Min.: 0 A, Max.: 4.9 A
    -
    -
    O2 Heater Curr Val B2S2
    Heated oxygen sensor current (bank 2 sensor 2)/
    Min.: 0 A, Max.: 4.9 A
    -
    -
    Short FT #1
    Short-term fuel trim (bank 1)/
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
    Long FT #1
    Long-term fuel trim (bank 1)/
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Total FT #1
    Total fuel trim (bank 1)
    Min.: -0.5, Max.: 0.496
    -0.28 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim (bank 2)/
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
    Long FT #2
    Long-term fuel trim (bank 2)/
    Min.: -100%, Max.: 99.2%
    -15 to 15%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Total FT #2
    Total fuel trim (bank 2)
    Min.: -0.5, Max.: 0.496
    -0.28 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (bank 1)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
    Fuel System Status #2
    Fuel system status (bank 2)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
    Air Pump Pressure (Absolute)
    Air pump pressure (absolute) (bank 1)/
    Min.: 0 kPa (0 mmHg), Max.: 65535 kPa (491553.1 mmHg)
    Atmospheric pressure +1 kPa (7.5 mmHg) or more: Air pump on, air switching valve (bank 1) open
    Close to atmospheric pressure: Air pump off, air switching valve (bank 1) closed
    Refer to DTC P2431 (Click here).
    Air Pump2 Pressure (Absolute)
    Air pump pressure (absolute) (bank 2)/
    Min.: 0 kPa (0 mmHg), Max.: 65535 kPa (491553.1 mmHg)
    Atmospheric pressure +1 kPa (7.5 mmHg) or more: Air pump on, air switching valve (bank 2) open
    Close to atmospheric pressure: Air pump off, air switching valve (bank 2) closed
    Refer to DTC P2431 (Click here).
    Air Pump Pulsation Pressure
    Air pump pulsation pressure/
    Min.: 0 kPa (0 mmHg), Max.: 655.35 kPa (4915.531 mmHg)
    -
    Cumulative pulsation pressure calculated by ECM (Click here).
    Secondary Air Control VSV
    Secondary air injection system status/
    ON or OFF
    ON: Secondary air injection system operating
    -
    AI Test
    AI operation prohibition/
    READY or NOT RDY
    READY
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg, Max.: 63.5 deg
    BTDC 7 to 24°: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    -22 to 0° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    0 to 22° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Idle Spark Advn Ctrl #1
    Individual cylinder timing advance compensation amount (No. 1)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #2
    Individual cylinder timing advance compensation amount (No. 2)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #3
    Individual cylinder timing advance compensation amount (No. 3)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #4
    Individual cylinder timing advance compensation amount (No. 4)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #5
    Individual cylinder timing advance compensation amount (No. 5)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #6
    Individual cylinder timing advance compensation amount (No. 6)/
    Min.: 0°CA, Max.: 15.93°CA
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    ACIS VSV
    VSV status for ACIS control/
    ON or OFF
    -
    -
    VVT Control Status #1
    Variable valve timing (VVT) control status (bank 1)/
    ON or OFF
    -
    -
    VVT Control Status #2
    VVT control status (bank 2)/
    ON or OFF
    -
    -
    VVT Advance Fail
    VVT control failure status/
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1*2
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #1*2
    VVT change angle (bank 1)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #1*2
    VVT camshaft timing oil control valve operation duty (bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Aim Angle #2*2
    VVT aim angle (bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #2*2
    VVT change angle (bank 2)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #2*2
    VVT camshaft timing oil control valve operation duty (bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1, Sensor 1)/
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B2S1
    Catalyst temperature (Bank 2, Sensor 1)/
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1, Sensor 2)/
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B2S2
    Catalyst temperature (Bank 2, Sensor 2)/
    Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal
    Power steering switch signal/
    ON or OFF
    ON: Power steering operation
    -
    Neutral Position SW Signal*3
    PNP switch status/
    ON or OFF
    ON: P or N position
    -
    Clutch Switch*4
    Clutch Switch status/
    ON or OFF
    ON: Clutch pedal depressed
    -
    4WD SW*5
    4WD switch status/
    ON or OFF
    ON: 4WD ON
    -
    Transfer L4*3
    Transfer L4 switch status/
    ON or OFF
    ON: Transfer L4 ON
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to the Check Mode Procedure
    (Click here).
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    AS Test Result
    Check mode result for secondary air injection system/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C Monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C Monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Component Monitor ENA
    Comprehensive component monitor/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor/
    Compl or Incmpl
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor/
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor/
    Compl or Incmpl
    -
    -
    Misfire Monitor ENA
    Misfire monitor/
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor/
    Compl or Incmpl
    -
    -
    EGR/VVT Monitor ENA
    EGR monitor/
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR monitor/
    Compl or Incmpl
    -
    -
    Heater Monitor ENA
    O2S (A/FS) heater monitor/
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor ENA
    O2S (A/FS) monitor/
    Unable or Enable
    -
    -
    O2S(A/FS) Monitor CMPL
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor ENA
    A/C monitor/
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor ENA
    2nd air monitor/
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor ENA
    EVAP monitor/
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Cat Monitor ENA
    Heated catalyst monitor/
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status/
    ON or OFF
    -
    -
    # Codes (Include History)
    Number of codes/
    Min.: 0, Max.: 255
    -
    Number of stored DTCs.
    MIL
    MIL status/
    ON or OFF
    ON: MIL on
    -
    MIL ON Run Distance
    MIL on run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL on
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after the DTC is cleared.
    Dist Batt Cable Disconnect
    Distance from battery cable disconnected/
    Min.: 0 km, Max.: 65535 km
    -
    -
    IG OFF Elapsed Time
    Time after ignition switch off/
    Min.: 0 min, Max.: 655350 min
    -
    -
    OBD Requirements
    OBD requirement
    OBD II (California ARB)
    -
    Number of Emission DTC
    Emission related DTCs
    -
    Number of emission related DTCs.
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 65535
    0 to 600
    -
    Cylinder #1 Misfire Count
    to
    Cylinder #6 Misfire Count
    Misfire count of the cylinder 1 to 6/
    Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0
    -
    Misfire RPM
    Engine speed for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire margin:
    Min.: -128%, Max.: 127%
    0 to 99.22%
    Misfire detecting margin
    Catalyst OT MF F/C
    Catalyst over temperature misfire prevention F/C/
    Not Avl or Avail
    Avail: Cat OT MF F/C available
    Not Avl: Cat OT MF F/C not available
    -
    Cat OT MF F/C History
    Catalyst over temperature misfire prevention F/C history/
    ON or OFF
    OFF: Fuel cut operation not exists
    -
    Cat OT MF F/C Cylinder #1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #5
    Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #6
    Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Engine Speed (Starter Off)
    Engine speed when starter off/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Starter Count
    Number of times starter turned on after ignition switch turned to ON/
    Min.: 0, Max.: 255
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Run Dist of Previous Trip
    Distance driven during previous trip/
    Min.: 0 km, Max.: 655.35 km
    -
    Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
    After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

    HINT:
    Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

    Engine Starting Time
    Time elapsed after engine started (interval between ignition switch to ON and off)/
    Min.: 0 ms, Max.: 655350 ms
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Previous Trip Coolant Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Previous Trip Intake Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Engine Oil Temperature
    Engine oil temperature (estimated temperature)/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Previous Trip Eng Oil Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Ambient Temp for A/C
    Ambient temperature for A/C/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Previous Trip Ambient Temp
    Ambient temperature during previous trip/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    Engine Start Hesitation
    History of hesitation during engine start/
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine start/
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    Check the value when the engine stalls, is difficult to start, or idles roughly
    A/F Learn Value Idle #1
    Air fuel ratio learned value for idling (bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #1
    Air fuel ratio learned value for low engine loads (bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #1
    Air fuel ratio learned value for midsized engine loads 1 (bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #1
    Air fuel ratio learned value for midsized engine loads 2 (bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #1
    Air fuel ratio learned value for high engine loads (bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Idle #2
    Air fuel ratio learned value for idling (bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #2
    Air fuel ratio learned value for low engine loads (bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #2
    Air fuel ratio learned value for midsized engine loads 1 (bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #2
    Air fuel ratio learned value for midsized engine loads 2 (bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #2
    Air fuel ratio learned value for high engine loads (bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    -
    Brake Override System
    Brake override system status/
    ON or OFF
    ON: Brake override system operating
    -
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operation
    The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
    Immobiliser Fuel Cut
    Status of immobiliser fuel cut/
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of the immobiliser fuel cut history/
    ON or OFF
    -
    -
    Electrical Load Signal 1
    Electrical load signal/
    ON or OFF
    -
    -
    Electrical Load Signal 2
    Electrical load signal/
    ON or OFF
    -
    -
    Model Code
    Model code
    -
    Identifying the model code:
    GRN2#.
    Engine Type
    Engine type
    -
    Identifying the engine type:
    1GRFE.
    Cylinder Number
    Number of cylinders/
    Min.: 0, Max.: 255
    -
    Identifying the number of cylinders:
    6.
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    MT or ECT.
    Destination
    Destination
    -
    Identifying the destination:
    A (America).
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying the model year:
    20##.
    System Identification
    System identification
    -
    Identifying the engine system:
    Gasoline (gasoline engine).
    Engine Speed of Cyl #1
    Engine speed for cylinder 1/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #2
    Engine speed for cylinder 2/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #3
    Engine speed for cylinder 3/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #4
    Engine speed for cylinder 4/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #5
    Engine speed for cylinder 5/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #6
    Engine speed for cylinder 6/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Av Engine Speed of All Cyl
    Engine speed for all cylinders/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    A/F Sensor Determination (worst value) #1
    Worst judgment value of air fuel ratio sensor output (bank 1)/
    Min.: -1, Max.: 0.99
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    A/F Sensor Determination (worst value) #2
    Worst judgment value of air fuel ratio sensor output (bank 2)/
    Min.: -1, Max.: 0.99
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #1
    Worst value of average engine speed fluctuation (Cylinder 1)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #2
    Worst value of average engine speed fluctuation (Cylinder 2)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #3
    Worst value of average engine speed fluctuation (Cylinder 3)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #4
    Worst value of average engine speed fluctuation (Cylinder 4)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #5
    Worst value of average engine speed fluctuation (Cylinder 5)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    Engine Speed Fluctuation Avg (worst value) #6
    Worst value of average engine speed fluctuation (Cylinder 6)/
    Min.: 0, Max.: 2.55
    0.00
    1. The worst value detected during monitoring is displayed.
    2. The value is reset when DTCs are cleared.
    SPD (NT)*3
    Input shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    Data is displayed in increments of 50 rpm.
    SPD (SP2)*3
    Output shaft speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -

HINT:
  1. Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in P or N (Neutral), the A/C switch is off and all accessory switches are off.
  2. *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
  3. *2: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1) and Control the VVT Linear (Bank 2). For other Active Tests, the Data List value will be 0.
  4. *3: for Automatic Transmission
  5. *4: for Manual Transmission
  6. *5: for 4WD


FOR MEXICO MODELS 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Injector (port)
Injection period of No. 1 cylinder/
Min.: 0 ms, Max.: 32.64 ms
1.6 to 2.7 msec.: Idling
-
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC 7 to 24°: Idling
-
Calculate Load
Calculated load by ECM/
Min.: 0%, Max.: 100%
  1. 10 to 40%: Idling
  1. 10 to 40%: Running without load (2000 rpm)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Air flow rate from MAF meter/
Min.: 0 gm/sec, Max.: 655.35 gm/sec
3.2 to 4.7 gm/sec: Idling
13.1 to 18.9 gm/sec: 2000 rpm
If the mass air flow volume is approximately 0.0 gm/sec:
  1. The mass air flow meter power source circuit is open or short.
  2. The VG circuit is open or short.
If the mass air flow volume is 271.0 gm/sec or more:
  1. The E2G circuit is open.
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383.75 rpm
650 to 750 rpm: Idling
-
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
The speed is indicated on speedometer
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (176 to 212°F):
After warming up
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is higher than 135°C (275°F): the sensor circuit is shorted.
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C (284°F)
Equivalent to ambient air temperature
If the value is higher than -40°C (-40°F): the sensor circuit is open.
If the value is 128°C (262°F): the sensor circuit is shorted.
Air-Fuel Ratio
Air fuel ratio/
Min.: 0, Max.: 1.999
0.8 to 1.2: Idling
-
Purge Density Learn Value
Learning value of purge density/
Min.: -50, Max.: 350
-35 to 1: Idling
Service data
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 102.4%
0 to 100%: Idling
-
EVAP (Purge) VSV
EVAP (Purge) VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling
Order signal from ECM
Vapor Pressure Pump
Vapor pressure/
Min.: 33.853 kPa (253.91 mmHg),
Max.: 125.596 kPa (942.04 mmHg)
Near atmosphere pressure: Fuel cap removed
Pressure inside fuel tank monitored by vapor pressure sensor.
Vapor Pressure (calculated)
Vapor pressure (calculated)/
Min.: -5.632 kPa (-42.24 mmHg),
Max.: 715.264 kPa (5364.92 mmHg)
Near atmosphere pressure: Fuel cap removed
Pressure inside fuel tank monitored by vapor pressure sensor.
Knock Correct Learn Value
Correction learning value of knocking/
Min.: -64°CA, Max.: 1984°CA
0 to 22°CA:
Driving, 70 km/h (44 mph)
Service data
Knock Feedback Value
Feedback value of knocking/
Min.: -64°CA, Max.: 1984°CA
-22 to 0°CA:
Driving, 70 km/h (44 mph)
Service data
Clutch Current
Clutch current/
Min.: 0 A, Max.: 2.49 A
-
-
Accelerator Position No. 1
Accelerator pedal position No. 1/
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal released
54 to 86%: Accelerator pedal fully depressed
-
Accelerator Position No. 2
Accelerator pedal position No. 2/
Min.: 0%, Max.: 100%
12 to 42%: Accelerator pedal released
66 to 98%: Accelerator pedal fully depressed
-
Accelerator Position No. 1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Accelerator Position No. 2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Accelerator Position No. 1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accelerator Position No. 2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: Accelerator pedal released
3.4 to 4.7 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Throttle Fully Closed Learn
Throttle valve fully closed
(learned value)/
Min.: 0 V, Max.: 5 V
0.4 to 1.0 V: Accelerator pedal released
-
Accel Fully Close #1 AD
Accelerator fully closed value No. 1 (AD)/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Accel Fully Close Learn #1
Accelerator fully closed learning value No. 1/
Min.: 0 deg., Max.: 124.512 deg.
-
ETCS service data
Accel Fully Close Learn #2
Accelerator fully closed learning value No. 2/
Min.: 0 deg., Max.: 124.512 deg.
-
ETCS service data
Fail Safe Drive
Whether or not fail-safe function executed/
ON or OFF
  1. ON: ETCS has failed
  2. OFF: ETCS normal
ETCS service data
Fail Safe Drive (Main CPU)
Whether or not fail-safe function executed/
ON or OFF
  1. ON: ETCS has failed
  2. OFF: ETCS normal
ETCS service data
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal released
-
System Guard
System guard/
ON or OFF
-
ETCS service data
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
  1. ON: Accelerator pedal released
  2. OFF: Accelerator pedal fully depressed
-
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position
Throttle valve opening percentage according to throttle position sensor/
Min.: 0%, Max.: 100%
  1. 10 to 22%: Accelerator pedal released
  2. 64 to 96%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA1.
Throttle Sensor Position #2
Throttle valve opening percentage according to throttle position sensor No. 2/
Min.: 0%, Max.: 100%
  1. 42 to 62%: Accelerator pedal released
  2. 92 to 100%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA2.
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 5 V
  1. 0.5 to 1.1 V: Accelerator pedal released
  2. 3.2 to 4.8 V: Accelerator pedal fully depressed
  3. 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 5 V
  1. 2.1 to 3.1 V: Accelerator pedal released
  2. 4.6 to 5.0 V: Accelerator pedal fully depressed
  3. 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V
-
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1/
Min.: 0 V, Max.: 4.9804 V
0.6 to 1.4 V
ETCS service data
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2/
Min.: 0 V, Max.: 4.9804 V
1.7 to 2.5 V
ETCS service data
Throttle Sens Open #1 (AD)
Throttle position sensor No. 1 output voltage (AD)/
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V
-
Throttle Motor
Whether throttle actuator control permitted/
ON or OFF
  1. ON: Ignition switch ON
  2. OFF: ETCS has failed
-
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 80 A
0 to 3.0 A: Idling
-
Throttle Motor
Throttle actuator/
Min.: 0%, Max.: 100%
0.5 to 40%: Idling
-
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.92 A
0 to 3.0 A: Idling
-
Throttle Motor Open Duty
Throttle actuator duty ratio/
Min.: 0%, Max.: 100%
0 to 40%: Idling
ETCS service data
Throttle Motor Close Duty
Throttle actuator duty ratio/
Min.: 0%, Max.: 100%
0 to 40%: Idling
ETCS service data
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 100%
-
-
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 100%
-
-
O2S B1S2
Heated oxygen sensor output voltage (bank 1 sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving, 70 km/h (44 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
O2S B2S2
Heated oxygen sensor output voltage (bank 2 sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving, 70 km/h (44 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS B1S1
Air fuel ratio sensor output voltage (bank 1 sensor 1)/
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS B2S1
Air fuel ratio sensor output voltage (bank 2 sensor 1)/
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS B2S1
Air fuel ratio sensor output current (bank 2 sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
Total FT #1
Total fuel trim (bank 1)
Average value for fuel trim system of (bank 1)/
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
-
Total FT #2
Total fuel trim (bank 1)
Average value for fuel trim system (bank 2)/
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
-
Short FT #1
Short-term fuel trim (bank 1)/
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim (bank 1)/
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Short FT #2
Short-term fuel trim (bank 2)/
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #2
Long-term fuel trim (bank 2)/
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Fuel System Status (Bank 1)
Fuel system status (bank 1)/
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning
Fuel System Status (Bank 2)
Fuel system status (bank 2)/
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning
O2FT B1S2
Short-term fuel trim associated (bank 1 sensor 2)/
Min.: -100%, Max.: 99.2%
-20 to 20%
-
O2FT B2S2
Short-term fuel trim associated (bank 2 sensor 2)/
Min.: -100%, Max.: 99.2%
-20 to 20%
-
AF Lambda B1S1
Short-term fuel trim associated (bank 1 sensor 1)/
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  1. Stoichiometric air fuel ratio = 1
  1. Value greater than 1 (1.001 to 1.999) = Lean
-
AFS B1S1
Air fuel ratio sensor output current (bank 1 sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AF FT B2S1
Short-term fuel trim associated (bank 2 sensor 1)/
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  1. Stoichiometric air fuel ratio = 1
  1. Value greater than 1 (1.001 to 1.999) = Lean
-
Catalyst Temp (B1S1)
Catalyst temperature (bank 1 sensor 1)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
-
Catalyst Temp (B2S1)
Catalyst temperature (bank 2 sensor 1)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
-
Catalyst Temp (B1S2)
Catalyst temperature (bank 1 sensor 2)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
-
Catalyst Temp (B2S2)
Catalyst temperature (bank 2 sensor 2)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
-
Sub O2S Impedance B1S2
Heated oxygen sensor impedance (bank 1 sensor 2)/
Min.: 0 Ω, Max.: 21247.68 Ω
5 to 15000 Ω
After driving for approx. 10 min. in an urban area.
Sub O2S Impedance B2S2
Heated oxygen sensor impedance (bank 2 sensor 2)/
Min.: 0 Ω, Max.: 21247.68 Ω
5 to 15000 Ω
After driving for approx. 10 min. in an urban area.
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
Coolant temperature when engine started
Service data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
Intake air temperature when engine started
Service data
Injection Volum (Cylinder 1)
Injection volume (Cylinder 1)/
Min.: 0 ml, Max.: 2.048 ml
0.005 to 0.015 ml: Idling
Quantity of fuel injection volume for 10 times
Starter Signal
Starter signal/
ON or OFF
ON: Cranking
-
Power Steering Switch
Power steering switch/
ON or OFF
ON: Power steering operation
-
Power Steering Signal
Power steering signal (history)/
ON or OFF
ON: When steering wheel first turned after battery terminals connected
This signal status usually ON until battery terminals disconnected
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
  1. ON: Throttle fully closed
  1. OFF: Throttle open
-
A/C Signal
A/C switch status/
ON or OFF
ON: A/C ON
-
Neutral Position SW Signal*2
PNP switch status
ON or OFF
ON: P or N position
-
Electrical Load Signal
Electrical load signal/
ON or OFF
-
-
Stop Light Switch
Stop light switch status/
ON or OFF
ON: Brake pedal depressed
-
ETCS Actuator Power
ETCS power supply/
ON or OFF
  1. ON: Ignition switch to ON and system normal
  2. OFF: ETCS has failed
-
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 19.92 V
11 to 14 V: Ignition switch ON and system normal
ETCS service data
Battery Voltage
Battery voltage/
Min.: 0, Max.: 65.535 V
11 to 14 V: Idling
-
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
-
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa, Max.: 150 kPa
Equivalent to atmospheric pressure (absolute pressure)
-
Fuel Pump Speed Control
Fuel pump speed control status/
ON/H or OFF/L
ON: Idling
-
ACIS VSV
VSV status for ACIS control/
ON or OFF
-
-
ACT VSV
A/C cut status for Active Test/
ON or OFF
-
-
VVT Control Status (Bank2)
VVT control (bank 2) status/
ON or OFF
-
-
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
-
Fuel Pump/Speed Status
Fuel pump/status/
ON or OFF
-
-
VVT Control Status (Bank1)
VVT control (bank 1) status/
ON or OFF
-
-
Vacuum Pump
Key-OFF EVAP system leak detection pump status/
ON or OFF
-
-
EVAP System Vent Valve
Key-OFF EVAP system vent valve status/
ON or OFF
-
-
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
-
Engine Speed of Cyl #1
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #2
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #3
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #4
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #5
Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #6
Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
An Engine Speed of All Cyl
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
VVT Aim Angle (Bank1)*1
VVT aim angle (bank 1)/
Min.: 0%, Max.: 100%
0 to 80%
VVT duty signal value during intrusive operation
VVT Change Angle (Bank1)*1
VVT change angle (bank 1)/
Min.: 0° FR, Max.: 60° FR
0 to 5° FR: Idling
Displacement angle during intrusive operation
VVT OCV Duty (Bank1)*1
VVT camshaft timing oil control valve operation duty (bank 1)/
Min.: 0%, Max.: 100%
0 to 100%
Requested duty value for intrusive operation
VVT Aim Angle (Bank2)*1
VVT aim angle (bank 2)/
Min.: 0%, Max.: 100%
0 to 80%
VVT duty signal value during intrusive operation
VVT Change Angle (Bank2)*1
VVT change angle (bank 2)/
Min.: 0° FR, Max.: 60° FR
0 to 5° FR: Idling
Displacement angle during intrusive operation
VVT OCV Duty (Bank2)*1
VVT camshaft timing oil control valve operation duty (bank 2)/
Min.: 0%, Max.: 100%
0 to 100%
Requested duty value for intrusive operation
Idle Fuel Cut
Fuel cut idle/
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed is more than 2800 rpm
FC TAU
Fuel cut TAU (Fuel cut during very light load)/
ON or OFF
ON: Fuel cut operation
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Ignition
Number of counts of misfire counter/
Min.: 0, Max.: 600
0 to 600
-
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
Misfire count of cylinder 1 to 6/
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
All cylinders misfire count/
Min.: 0, Max.: 255
0
-
Misfire RPM
Average engine speed during misfire/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Average load during misfire/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire margin/
Min.: -100%, Max.: 99.22%
-100 to 99.22%
Misfire detecting margin
Catalyst OT MF F/C
Catalyst over temperature misfire prevention F/C/
Not Avl or Avail
Avail: Cat OT MF F/C available
Not Avl: Cat OT MF F/C not available
-
Cat OT MF F/C History
Catalyst over temperature misfire prevention F/C history/
ON or OFF
OFF: Fuel cut operation not exists
-
Cat OT MF F/C Cylinder #1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
# Codes
Number of detected DTCs/
Min.: 0, Max.: 255
-
-
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
Refer to the Check Mode Procedure (Click here).
SPD Test
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
Misfire Test
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS2 Test
Check mode result for HO2 sensor (bank 2)/
Compl or Incmpl
-
-
OXS1 Test
Check mode result for HO2 sensor (bank 1)/
Compl or Incmpl
-
-
A/F Test Results (Bank 2)
Check mode result for air fuel ratio sensor (bank 2)/
Compl or Incmpl
-
-
A/F Test Results (Bank 1)
Check mode result for air fuel ratio sensor (bank 1)/
Compl or Incmpl
-
-
MIL
MIL status/
ON or OFF
ON: MIL on
-
MIL ON Run Distance
MIL ON run distance/
Min.: 0 km,
Max.: 65535 km
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min.,
Max.: 65535 min.
Equivalent to running time after MIL on
-
Engine Run Time
Engine run time/
Min.: 0 s,
Max.: 65535 s
Time after engine start
Service data.
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min.,
Max.: 65535 min.
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTC cleared
OBD Requirements
OBD requirement
OBD2
-
Number of Emission DTC
Emission related DTCs
-
Number of emission related DTCs
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
Component Monitor ENA
Comprehensive component monitor/
Unable or Enable
-
-
Component Monitor CMPL
Comprehensive component monitor/
Compl or Incmpl
-
-
Fuel System Monitor ENA
Fuel system monitor/
Unable or Enable
-
-
Fuel System Monitor CMPL
Fuel system monitor/
Compl or Incmpl
-
-
Misfire Monitor ENA
Misfire monitor/
Unable or Enable
-
-
Misfire Monitor CMPL
Misfire monitor/
Compl or Incmpl
-
-
EGR Monitor ENA
EGR monitor/
Unable or Enable
-
-
EGR Monitor CMPL
EGR monitor/
Compl or Incmpl
-
-
Heater Monitor ENA
O2S (A/FS) heater monitor/
Unable or Enable
-
-
Heater Monitor CMPL
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S (A/FS) Monitor ENA
O2S (A/FS) monitor/
Unable or Enable
-
-
O2S (A/FS) Monitor CMPL
O2S (A/FS) monitor/
Compl or Incmpl
-
-
A/C Monitor ENA
A/C monitor/
Unable or Enable
-
-
A/C Monitor CMPL
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor ENA
2nd air monitor/
Unable or Enable
-
-
2nd Air Monitor CMPL
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor ENA
EVAP monitor/
Unable or Enable
-
-
EVAP Monitor CMPL
EVAP monitor/
Compl or Incmpl
-
-
Heated Cat Monitor ENA
Heated catalyst monitor/
Unable or Enable
-
-
Heated Cat Monitor CMPL
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor ENA
Catalyst monitor/
Unable or Enable
-
-
Catalyst Monitor CMPL
Catalyst monitor/
Compl or Incmpl
-
-
Model Code
Model code
-
Identifying the model code:
GRN2#
Engine Type
Engine type
-
Identifying the engine type:
1GRFE
Cylinder Number
Cylinder number/
Min.: 0, Max.: 255
-
Identifying the number of cylinders:
6
Transmission Type
Transmission type
-
Identifying the transmission type:
M/T or ECT
Destination
Destination
-
Identifying the destination:
A (America)
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Identifying the model year:
20##
System Identification
System identification
-
Identifying the engine system:
Gasoline (Gasoline engine)

HINT:
  1. Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in P or N (Neutral), the A/C switch is off and all accessory switches are off.
  2. *1: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1) and Control the VVT Linear (Bank 2). For other Active Tests, the Data List value will be 0.
  3. *2: for Automatic Transmission


ACTIVE TEST

HINT:
Using the Techstream to perform the Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. According to the display on the Techstream, perform the Active Test.


Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5% and 24.8%
  1. All fuel injector assemblies are tested at the same time.
  2. Perform the test at 3000 rpm or less.
  3. Injection volume can be changed in fine gradations within the control range.
  4. Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.
  5. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  6. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
Control the Injection Volume for A/F Sensor
Change injection volume
-12.5% / 0% / 12.5%
  1. All fuel injector assemblies are tested at the same time.
  2. Perform the test at 3000 rpm or less.
  3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor voltage outputs.
  4. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  5. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
Activate the VSV for Secondary Air Control
Activate the secondary air system
OFF/ON
  1. Do not perform this test for 5 seconds or more.
  2. After the test, do not perform the test again for 30 seconds.
Activate the Fuel Pump Speed Control
Fuel pump speed control
OFF (high speed) / ON (low speed)
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Activate the VSV for Intake Control
Activate VSV for intake control
OFF/ON
Do not perform this test for 10 seconds or more.
Activate the VSV for Evap Control
Activate purge VSV control
OFF/ON
The valve is opened with a 30% duty ratio.
Control the A/C Cut Signal
Control A/C cut signal
OFF/ON
Test possible when following
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Control the Fuel Pump/Speed
Activate fuel pump
OFF/ON
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Connect the TC and TE1
Turn on and off TC and TE1 connection
OFF/ON
  1. ON: TC and TE1 connected.
  2. OFF: TC and TE1 disconnected.
  3. Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
OFF/ON
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Prohibit the Catalyst OT Misfire prevent F/C
Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
OFF/ON
ON: Fuel cut is prohibited
Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
Control the ETCS Open/Close Slow Speed
Throttle actuator
Open/Close
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Fully depressing the accelerator pedal (accelerator pedal angle: 58 degrees or more).
  4. Shift lever is in P (Neutral).
Control the ETCS Open/Close Fast Speed
Throttle actuator
Open/Close
Same as above.
Control the VVT Linear (Bank 1)
Control VVT (Bank 1)
-128 to 127% This value added to present camshaft timing oil control valve control duty
100%: Maximum advance
-100%: Maximum retard
  1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
  2. Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P (Neutral).
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 1)
Camshaft timing oil control valve (bank 1) on and off
OFF/ON
  1. Engine stalls or idles roughly when camshaft timing oil control valve is turned on.
  2. Engine runs or idles normally when camshaft timing oil control valve is OFF.
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
  4. Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P (Neutral).
Control the VVT Linear (Bank 2)
Control VVT (bank 2)
-128 to 127% This value added to present camshaft timing oil control valve control duty
100%: Maximum advance
-100%: Maximum retard
  1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
  2. Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P (Neutral).
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 2)
Camshaft timing oil control valve (bank 2) on and off
OFF/ON
  1. Engine stalls or idles roughly when camshaft timing oil control valve is turned on.
  2. Engine runs or idles normally when camshaft timing oil control valve is OFF.
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
  4. Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P (Neutral).
Activate the Vacuum Pump
Activate leak detection pump (built into canister pump module)
OFF/ON
Refer to EVAP System (Click here)
Activate the VSV for Vent Valve
Activate vent valve (built into canister pump module)
OFF/ON
Refer to EVAP System (Click here)
Control the Select Cylinder Fuel Cut
Selected cylinder (cylinder #1 to #6) injector fuel cut
#1/#2/#3/#4/#5/#6
OFF/ON
Perform this test when the following conditions are met:
  1. Vehicle is stopped.
  2. Engine is idling.
  3. Shift lever is in P (Neutral).
*1
Control the All Cylinders Fuel Cut
All cylinder fuel cut
OFF/ON
Perform this test when the following conditions are met:
  1. Vehicle is stopped.
  2. Engine is idling.
  3. Shift lever is in P (Neutral).
*1
Check the Cylinder Compression
Check the cylinder compression pressure
OFF/ON
Fuel injection and ignition stop in all cylinders.
*2
Check the Imbalance Cylinder
Selected cylinder (cylinder #1 to #6) fuel injection volume change
Between 50 and 200%
  1. Perform this test when the following conditions are met:
    1. Engine is warmed up and is idling.
    2. Shift lever is in P (Neutral).
  2. At the time this Active Test item is entered = 100%
    1. Below 100% = Fuel injection volume is decreased
    2. Higher than 100% = Fuel injection volume is increased
  3. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Imbalance Cylinder / Gas AF Control / A/F Sensor Determination (worst value) and Engine Speed Fluctuation Avg (worst value).
  4. Refer to DTC P219A, P219B (Click here).

NOTICE:
*1:
  1. If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
  2. If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
    1. Stop the engine and turn the ignition switch to ON.
    2. Enter the Control the Select Cylinder Fuel Cut.
    3. Select the cylinder for fuel cut (cylinder #1 to #6) and turn the Active Test ON (press the RIGHT or LEFT button).
    4. Start the engine.

HINT:
*2: In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

  7. Push the snapshot button to turn the snapshot function on.

    HINT:
    Using the snapshot function, data can be recorded during the Active Test.

  8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

    HINT:
    After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

  9. Crank the engine for about 10 seconds.

    HINT:
    Continue to crank the engine until the values change from the default value (51199 rpm).

  10. Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the Techstream.

    HINT:
    At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    NOTICE:
    1. Do not crank the engine continuously for 20 seconds or more.
    2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
    3. Use a fully-charged battery.

  11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

    NOTICE:
    If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

  12. Push the snapshot button to turn the snapshot function off.
  13. Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

    HINT:
    If the data is not displayed as a graph, the change of the values cannot be observed.

  14. Check the change in engine speed values.

    HINT:
    As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.


FOR MEXICO MODELS 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5% and 24.8%
  1. All fuel injector assemblies are tested at the same time.
  2. Perform the test at 3000 rpm or less.
  3. Injection volume can be changed in fine gradations within the control range.
  4. Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.
  5. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  6. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
Control the Injection Volume for A/F Sensor
Change injection volume
-12.5% / 0% / 12.5%
  1. All fuel injector assemblies are tested at the same time.
  2. Perform the test at 3000 rpm or less.
  3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor voltage outputs.
  4. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  5. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
Activate the Fuel Pump Speed Control
Fuel pump speed control
ON (low speed) /OFF (high speed)
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Activate the VSV for Intake Control
Activate VSV for intake control
ON/OFF
Do not perform this test for 10 seconds or more.
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
The valve is opened with a 30% duty ratio.
Control the A/C Cut Signal
Control A/C cut signal
ON/OFF
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Control the Fuel Pump / Speed
Activate fuel pump
ON/OFF
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON/OFF
  1. ON: TC and TE1 connected.
  2. OFF: TC and TE1 disconnected.
  3. Perform this test when the following conditions are met:
    1. Ignition switch to ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
Prohibit the Catalyst OT Misfire prevent F/C
Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
ON/OFF
ON: Fuel cut is prohibited
Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Fully depressing the accelerator pedal (accelerator pedal angle: 58 degrees or more).
  4. Shift lever is in P (Neutral).
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Same as above.
Control the VVT Linear (Bank 1)
Control VVT (bank 1)
-128 to 127% This value added to present camshaft timing oil control valve control duty
100%: Maximum advance
-100%: Maximum retard
  1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
  2. Perform this test when the following conditions are met:
    1. Ignition switch to ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 1)
Camshaft timing oil control valve (bank 1) on and off
ON/OFF
  1. Engine stalls or idles roughly when camshaft timing oil control valve is turned on.
  2. Engine runs or idles normally when camshaft timing oil control valve is OFF.
  3. Perform this test when the following conditions are met:
    1. Ignition switch to ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
  4. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT Linear (Bank 2)
Control VVT (bank 2)
-128 to 127% This value added to present camshaft timing oil control valve control duty
100%: Maximum advance
-100%: Maximum retard
  1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
  2. Perform this test when the following conditions are met:
    1. Ignition switch to ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 2)
Camshaft timing oil control valve (bank 2) on and off
ON/OFF
  1. Engine stalls or idles roughly when camshaft timing oil control valve is turned on.
  2. Engine runs or idles normally when camshaft timing oil control valve is OFF.
  3. Perform this test when the following conditions are met:
    1. Ignition switch to ON.
    2. Engine is stopped.
    3. Shift lever is in P (Neutral).
  4. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Activate the Vacuum Pump
Activate leak detection pump (built into canister pump module)
ON/OFF
Refer to EVAP System (Click here)
Activate the VSV for Vent Valve
Activate vent valve (built into canister pump module)
ON/OFF
Refer to EVAP System (Click here)
Control the Select Cylinder Fuel Cut
Selected cylinder (cylinder #1 to #6) injector fuel cut
#1/#2/#3/#4/#5/#6
OFF/ON
Perform this test when the following conditions are met:
  1. Vehicle is stopped.
  2. Engine is idling.
  3. Shift lever is in P (Neutral).
*1
Control the All Cylinders Fuel Cut
All cylinder fuel cut
ON/OFF
Perform this test when the following conditions are met:
  1. Ignition switch to ON.
  2. Engine is stopped.
  3. Shift lever is in P (Neutral).
*1
Check the Cylinder Compression
Check the cylinder compression pressure
ON/OFF
Fuel injection and ignition stop in all cylinders.
*2

NOTICE:
*1:
  1. If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
  2. If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
    1. Stop the engine and turn the ignition switch to ON.
    2. Enter the Control the Select Cylinder Fuel Cut.
    3. Select the cylinder for fuel cut (cylinder #1 to #6) and turn the Active Test ON (press the RIGHT or LEFT button).
    4. Start the engine.

HINT:
*2: In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

  7. Push the snapshot button to turn the snapshot function on.

    HINT:
    Using the snapshot function, data can be recorded during the Active Test.

  8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

    HINT:
    After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

  9. Crank the engine for about 10 seconds.

    HINT:
    Continue to crank the engine until the values change from the default value (51199 rpm).

  10. Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the Techstream.

    HINT:
    At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    NOTICE:
    1. Do not crank the engine continuously for 20 seconds or more.
    2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
    3. Use a fully-charged battery.

  11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

    NOTICE:
    If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

  12. Push the snapshot button to turn the snapshot function off.
  13. Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

    HINT:
    If the data is not displayed as a graph, the change of the values cannot be observed.

  14. Check the change in engine speed values.

    HINT:
    As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.


SYSTEM CHECK

HINT:
Performing a System Check in the Utility menu enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, System Check can show whether or not any DTCs are stored, and can detect potential malfunctions in the system.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.


Tester Display
Test Part
Control Range
Diagnostic Note
Evaporative System Check
(Automatic Mode)
Perform 6 steps in order to operate EVAP key-off monitor automatically
35°C (95°F) or less
  1. If no DTCs in Pending after performing this test, system functioning normally
  1. Refer to EVAP system (Click here)
Evaporative System Check
(Manual Mode)
Perform 6 steps in order to operate EVAP key-off monitor manually
35°C (95°F) or less
  1. Used to detect malfunctioning parts
  1. Refer to EVAP system (Click here)
Secondary Air Injection Check (Automatic Mode)
Perform secondary air injection system operation automatically
With warm engine, ignition switch turned off once
  1. If no pending DTCs are output after performing this test, the system is functioning normally.
  2. Refer to the inspection procedure for secondary air injection system DTCs.
  3. When performing Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when System Check finishes
Secondary Air Injection Check (Manual Mode)
Perform 5 operations in order to operate air injection system monitor manually
With warm engine, ignition switch turned off once
  1. Used to detect malfunctioning parts.
  2. Refer to the inspection procedure for secondary air injection system DTCs.
  3. When performing Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when System Check finishes.