Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0560    System Voltage

for Preparation Click here


MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the stored ECM data is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.


MONITOR STRATEGY


Related DTCs
P0560: ECM System Voltage
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


Stand-by RAM
Initialized
Battery voltage
Less than 3.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0560.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A237490E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT ECM (BATT VOLTAGE)
A065741E11
  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-3 (BATT) - E4-3 (E1)
    Always
    9 to 14 V



OK
REPLACE ECM (Click here)
NG


2.CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)
A113677E04
  1. Check the harness and the connector between the EFI fuse and ECM.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the E8 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      2 (EFI fuse) - E8-3 (BATT)
      Always
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connection
      Condition
      Specified Condition
      2 (EFI fuse) or E8-3 (BATT) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the positive battery terminal.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal - 1 (EFI fuse)
      Always
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal or 1 (EFI fuse) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT BATTERY
  1. Check that the battery is not depleted.



NG
REPLACE BATTERY
OK

CHECK AND REPLACE ENGINE ROOM RELAY BLOCK