Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is stored, check No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is stored, check No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is stored, check No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is stored, check No. 4 ignition coil assembly circuit.


DESCRIPTION

A direct ignition system is used on this vehicle.
The direct ignition system is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A252500E02


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM
  3. No. 1 to No. 4 ignition coil assemblies
  4. ECM
  1. Reference: Inspection using an oscilloscope.

  2. A093278E44
    While cranking or idling, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    ECM Terminal Name
    (a) IGT1, IGT2, IGT3, IGT4 and E1
    (b) IGF1 and E1
    Tester Range
    2 V/DIV, 20 msec./DIV
    Condition
    Idling

MONITOR DESCRIPTION


A082388E39

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (Cylinder 1) Malfunction
P0352: Igniter (Cylinder 2) Malfunction
P0353: Igniter (Cylinder 3) Malfunction
P0354: Igniter (Cylinder 4) Malfunction
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
0.256 seconds for 2 times
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions A or B met
-
A. Engine speed
1500 rpm or less
B. Starter
OFF
Either of following conditions C or D met
-
C. Both of following conditions (a) and (b) met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or more
D. All of following conditions (a), (b) and (c) met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or more
(c) Number of sparks after CPU reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


IGF signal
ECM does not receive any IGF signal despite ECM sending IGT signal to igniter

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353 or P0354.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A236798E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check DTCs displayed on the Techstream.
    Result 
    Result
    Proceed to
    Same DTC output
    A
    Other ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY
A


2.INSPECT ECM (IGT1, IGT2, IGT3, IGT4 AND IGF1 SIGNAL)
A240486E01
  1. Inspect the ECM using an oscilloscope.

  1. While cranking or idling, check the waveform between the terminals of the E4 ECM connector.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E4-17 (IGT1) - E4-3 (E1)
    Cranking or idling
    Correct waveform shown
    E4-16 (IGT2) - E4-3 (E1)
    Cranking or idling
    Correct waveform shown
    E4-15 (IGT3) - E4-3 (E1)
    Cranking or idling
    Correct waveform shown
    E4-14 (IGT4) - E4-3 (E1)
    Cranking or idling
    Correct waveform shown
    E4-23 (IGF1) - E4-3 (E1)
    Cranking or idling
    Correct waveform shown



NG
REPLACE ECM (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
A113509E02
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    I1-2 (IGF) - E4-23 (IGF1)
    Always
    Below 1 Ω
    I2-2 (IGF) - E4-23 (IGF1)
    Always
    Below 1 Ω
    I3-2 (IGF) - E4-23 (IGF1)
    Always
    Below 1 Ω
    I4-2 (IGF) - E4-23 (IGF1)
    Always
    Below 1 Ω

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    I1-3 (IGT1) - E4-17 (IGT1)
    Always
    Below 1 Ω
    I2-3 (IGT2) - E4-16 (IGT2)
    Always
    Below 1 Ω
    I3-3 (IGT3) - E4-15 (IGT3)
    Always
    Below 1 Ω
    I4-3 (IGT4) - E4-14 (IGT4)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    I1-2 (IGF) or E4-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    I2-2 (IGF) or E4-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    I3-2 (IGF) or E4-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    I4-2 (IGF) or E4-23 (IGF1) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    I1-3 (IGT1) or E4-17 (IGT1) - Body ground
    Always
    10 kΩ or higher
    I2-3 (IGT2) or E4-16 (IGT2) - Body ground
    Always
    10 kΩ or higher
    I3-3 (IGT3) or E4-15 (IGT3) - Body ground
    Always
    10 kΩ or higher
    I4-3 (IGT4) or E4-14 (IGT4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A260249E02
  1. Disconnect the ignition coil assembly connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    I1-4 (GND) - Body ground
    Always
    Below 1 Ω
    I2-4 (GND) - Body ground
    Always
    Below 1 Ω
    I3-4 (GND) - Body ground
    Always
    Below 1 Ω
    I4-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the wire harness side connector.

    Standard Voltage :
    Tester Connection
    Condition
    Specified Condition
    I1-1 (+B) - I1-4 (GND)
    Always
    9 to 14 V
    I2-1 (+B) - I2-4 (GND)
    Always
    9 to 14 V
    I3-1 (+B) - I3-4 (GND)
    Always
    9 to 14 V
    I4-1 (+B) - I4-4 (GND)
    Always
    9 to 14 V



NG
Go to step 5
OK

REPLACE IGNITION COIL ASSEMBLY 

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH)
A113662E04
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the I7 ignition switch assembly connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    I1-1 (+B) - I7-6 (IG2)
    Always
    Below 1 Ω
    I2-1 (+B) - I7-6 (IG2)
    Always
    Below 1 Ω
    I3-1 (+B) - I7-6 (IG2)
    Always
    Below 1 Ω
    I4-1 (+B) - I7-6 (IG2)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    I1-1 (+B) or I7-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    I2-1 (+B) or I7-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    I3-1 (+B) or I7-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    I4-1 (+B) or I7-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY