Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the STA relay and also flows to terminal STA of the ECM (STA signal). The ECM uses the STA signal to control the fuel injection and ignition timing when the engine starts.

WIRING DIAGRAM


A254617E01


INSPECTION PROCEDURE

NOTICE:
  1. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if the engine can be cranked.

    Result 
    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked
    B



B
Go to step 15
A


2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to the ON and START position.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 8
OK


3.INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - STA RELAY - STARTER)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ignition switch connector.

  1. Disconnect the starter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I7-7 (ST2) - 5 (STA relay holder)
    Always
    Below 1 Ω
    3 (STA relay holder) - S6-1 (Starter)
    Always
    Below 1 Ω
    I7-7 (ST2) or 5 (STA relay holder) - Body ground
    Always
    10 kΩ or higher
    3 (STA relay holder) or S6-1 (Starter) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (ECM - STA RELAY - BODY GROUND)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E14-10 (STA) - 1 (STA relay holder)
    Always
    Below 1 Ω
    2 (STA relay holder) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT BATTERY
  1. Check that the battery is not depleted (Click here).

    OK:
    Battery is not depleted.



NG
CHARGE OR REPLACE BATTERY
OK


7.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

8.INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).

    Result 
    Result
    Proceed to
    OK
    (for Automatic Transmission)
    A
    OK
    (for Manual Transmission)
    B
    NG
    C



B
Go to step 12

C
REPLACE IGNITION SWITCH (Click here)
A


9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly .

    Result 
    Result
    Proceed to
    OK
    A
    NG
    (for A750F Automatic Transmission)
    B
    NG
    (for A750E Automatic Transmission)
    C



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A


10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the ignition switch connector.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I7-3 (ST1) - P1-4 (B)
    Always
    Below 1 Ω
    I7-3 (ST1) or P1-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (STA RELAY - ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    P1-5 (L) - E14-10 (STA)
    Always
    Below 1 Ω
    E14-10 (STA) - 1 (STA relay holder)
    Always
    Below 1 Ω
    2 (STA relay holder) - Body ground
    Always
    Below 1 Ω
    P1-5 (L) or E14-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

12.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch assembly .



NG
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - CLUTCH START SWITCH ASSEMBLY)
  1. Disconnect the ignition switch connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I7-3 (ST1) - C8-1
    Always
    Below 1 Ω
    I7-3 (ST1) or C8-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (STA RELAY - ECM - CLUTCH START SWITCH ASSEMBLY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C8-2 - E14-10 (STA)
    Always
    Below 1 Ω
    E14-10 (STA) - 1 (STA relay holder)
    Always
    Below 1 Ω
    2 (STA relay holder) - Body ground
    Always
    Below 1 Ω
    C8-2 or E14-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

15.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 16
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

16.CHECK HARNESS AND CONNECTOR (ECM - STA RELAY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E14-10 (STA) - 1 (STA relay holder)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)