Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control, rather than the conventional detecting method, which uses the locus ratio.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If a rich-lean cycle of the heated oxygen sensor is long, the oxygen storage capacity becomes greater. There is a direct correlation between the oxygen storage capacity of the heated oxygen sensor and the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, it illuminates the MIL and stores the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
The oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic)
  1. Front exhaust pipe assembly (TWC: Front and rear catalyst)
  2. Gas leakage from exhaust system
  3. Air fuel ratio sensor
  4. Heated oxygen sensor

CATALYST LOCATION


A260792E01


Text in Illustration 
*1
Exhaust Manifold
*2
Front Exhaust Pipe Assembly
*3
Tail Exhaust Pipe Assembly
*4
Air Fuel Ratio Sensor
*5
Heated Oxygen Sensor
*6
TWC: Front Catalyst
*7
TWC: Rear Catalyst
-
-

MONITOR STRATEGY


Related DTCs
P0420: Catalyst Deterioration
Required Sensors/Components (Main)
Three-way catalytic converter
Required Sensors/Components (Related)
Air fuel ratio sensor
Heated oxygen sensor
Intake air temperature sensor
Mass air flow meter
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
about 30 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010 (VVT Oil Control Valve)
P0011 (VVT System - Advance)
P0012 (VVT System - Retard)
P0016 (VVT System - Misalignment)
P0031, P0032 (Air Fuel Ratio Sensor Heater)
P0037, P0038 (Heated Oxygen Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop Fuel Control)
P0136, P0137, P0138, P0139, P0607 (Heated Oxygen Sensor)
P014C, P014D, P015A, P015B P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air Fuel Ratio Sensor)
P0171, P0172 (Fuel System)
P0301 - P0304 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0354 (Igniter)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0500 (Vehicle Speed Sensor)
P2440, P2441, P2444, P2445 (Secondary Air Injection System)
Battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
70°C (158°F) or more
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Idling
OFF
Engine RPM
Less than 4000 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10 to 80%
All of following conditions (a), (b), and (c) are met
-
(a) Mass air flow rate
2.5 to 50 gm/sec
(b) Front catalyst temperature
600 to 840°C (1112 to 1544°F)
(c) Rear catalyst temperature
475 to 760°C (887 to 1400°F)
Shift position
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC)
Less than 0.07 g

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A231470E90

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    NOTICE:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the catalyst efficiency monitor operates [C].

  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  12. Check if any DTCs (pending DTCs) are stored.

    HINT:
    If the monitor does not change to Complete, and no pending DTCs are stored, perform the following procedure.

  13. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [D].

    NOTICE:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the catalyst efficiency monitor operates [E].

  14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  15. Check if any DTCs (pending DTCs) are stored.

    HINT:
    If Catalyst does not change to Complete, and no pending DTCs are stored, extend the driving time.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E74

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream.

HINT:
  1. If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the Techstream.
  3. If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).

A240224E04


INSPECTION PROCEDURE

HINT:
  1. After performing repairs, drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern and check if DTC P0420 is output again. If a DTC is output again, replace the catalyst if it has not been replaced already.
  2. Sensor 1 refers to the sensor closest to the engine assembly.
  3. Sensor 2 refers to the sensor farthest away from the engine assembly.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    P0420 and other DTCs
    B

    HINT:
    If any DTCs other than P0420 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the Techstream on.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of - 12% to +12%. The injection volume can be changed in fine gradations.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard Voltage:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    +12%
    Rich
    Less than 3.1
    -12%
    Lean
    More than 3.4
    O2S B1S2
    (Heated oxygen)
    +12%
    Rich
    More than 0.55
    -12%
    Lean
    Less than 0.4


    Result 
    Status
    AFS Voltage B1S1
    Status
    O2S B1S2
    Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition
    Misfire
    Main Suspected Trouble Area
    Proceed To
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leakage from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leakage from exhaust system
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leakage from exhaust system
    Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently more than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume, the AFS Voltage B1S1 is consistently less than 3.1 V, and the O2S B1S2 is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 5

C
Go to step 6

D
Go to step 8
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the front exhaust pipe assembly (TWC: front and rear catalyst) (Click here).


NEXT

END 

5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
  1. Replace the air fuel ratio sensor (sensor 1) (Click here).



NEXT
Go to step 11

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


7.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)
  1. Replace the heated oxygen sensor (sensor 2) (Click here).



NEXT
Go to step 11

8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (Click here).



NEXT
Go to step 11

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC is not output
    (No pending DTCs output)
    B



B
END
A


12.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the front exhaust pipe assembly (TWC: front and rear catalyst) (Click here).


NEXT

END