Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No.
DTC Detection Condition
Trouble Area
P0171
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
  1. Intake system
  2. Injector blockage
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. A/F HEATER relay
  11. Air fuel ratio sensor heater and A/F HEATER relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
  15. Wire harness or connector
P0172
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
  1. Injector leakage or blockage
  2. Mass air flow meter
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. A/F HEATER relay
  11. Air fuel ratio sensor heater and A/F HEATER relay circuits
  12. ECM
  13. Wire harness or connector

HINT:
  1. When DTC P0171 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 is stored, the actual air fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 may be stored. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores the DTC.
Example:
The average fuel trim learning value is more than +35% or less than -35%, the ECM interprets this as a fuel system malfunction.

A082386E59


MONITOR STRATEGY


Related DTCs
P0171: Fuel Trim Lean
P0172: Fuel Trim Rich
Required Sensors/Components (Main)
Fuel system
Required Sensors/Components (Related)
Air fuel ratio sensor
Mass air flow meter
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
P0010 (VVT Oil Control Valve)
P0011 (VVT System - Advance)
P0012 (VVT System - Retard)
P0016 (VVT System - Misalignment)
P0031, P0032 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0354 (Igniter)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0500, P0722 (Vehicle Speed Sensor)
P2440, P2441, P2444, P2445 (Secondary Air Injection System)
Fuel system status
Closed-loop
Battery voltage
11 V or more
Catalyst Monitor
Not executed
Either of following conditions A or B set
-
A. Engine RPM
Below 1100 rpm
B. Intake air amount per revolution
0.22 g/rev. or more

for Automatic Transmission Models: 
Either of following conditions 1 or 2 met
-
1. Engine rpm
Below 1100 rpm
2. Intake air amount per revolution
0.22 g/rev. or more

for Manual Transmission Models: 
Either of following conditions 1 or 2 met
-
1. Engine rpm
Below 1100 rpm
2. Engine load
10% or more

TYPICAL MALFUNCTION THRESHOLDS


EVAP purge-cut
Executing
Either of following conditions met
-
Average between short-term fuel trim and long-term fuel trim
35% or more
Average between short-term fuel trim and long-term fuel trim
-35% or less

CONFIRMATION DRIVING PATTERN


A199233E83

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at a speed between 60 and 135 km/h (37 and 85 mph) for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.

  11. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A237272E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  5. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC P0171 or P0172 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling (press the Right or Left button to change the fuel injection volume).

  1. Monitor the voltage outputs of air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
  2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
  3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


Standard Voltage:

Techstream Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12%
Rich
Below 3.1 V
-12%
Lean
More than 3.4 V
O2S B1S2
(Heated oxygen)
+12%
Rich
More than 0.55
-12%
Lean
Less than 0.4


Result 
Status AFS Voltage B1S1
Status O2S B1S2
Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
Suspected Trouble Areas
Proceed to
Lean/Rich
Lean/Rich
Normal
-
A
Lean
Lean
Actual air fuel ratio lean
  1. PCV valve and hose
  2. PCV hose connections
  3. Fuel injector blockage
  4. Gas leakage from exhaust system
  5. Intake system
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
A
Rich
Rich
Actual air fuel ratio rich
  1. Fuel injector leakage or blockage
  2. Gas leakage from exhaust system
  3. Ignition system
  4. Fuel pressure
  5. Mass air flow meter
  6. Engine coolant temperature sensor
A
Lean
Lean/Rich
Air fuel ratio sensor malfunction
  1. Air fuel ratio sensor
B
Rich
Lean/Rich
Air fuel ratio sensor malfunction
  1. Air fuel ratio sensor
B
Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently more than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently less than 0.4 V.
Rich: During Control the Injection Volume, the AFS Voltage B1S1 is consistently less than 3.1 V, and the O2S B1S2 is consistently more than 0.55 V.
Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.

HINT:
Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here).



B
Go to step 11
A


5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


6.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 8.0 gm/sec. and 14.7 gm/sec.



NG
Go to step 16
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAKS
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK AND IGNITION
  1. Perform spark test (Click here).

    HINT:
    If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the injection and volume .

    HINT:
    If the injectors malfunction, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)


    A240487E01
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)



NG
Go to step 21
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A4-1 (HA1A) - E4-1 (HA1A)
    Always
    Below 1 Ω
    A4-3 (A1A+) - E4-21 (A1A+)
    Always
    Below 1 Ω
    A4-4 (A1A-) - E4-31 (A1A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A4-1 (HA1A) or E4-1 (HA1A) - Body ground
    Always
    10 kΩ or higher
    A4-3 (A1A+) or E4-21 (A1A+) - Body ground
    Always
    10 kΩ or higher
    A4-4 (A1A-) or E4-31 (A1A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    M1-3 (VG) - E5-28 (VG)
    Always
    Below 1 Ω
    M1-2 (E2G) - E5-30 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    M1-3 (VG) or E5-28 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter.

    HINT:
    If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0171 or P0172 is output
    B



B
REPLACE ECM (Click here)
A

END 

21.CHECK HARNESS AND CONNECTOR (A/F HEATER RELAY - AIR FUEL RATIO SENSOR)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+B) - 3 (A/F HEATER relay holder)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A4-2 (+B) - 3 (A/F HEATER relay holder)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT A/F HEATER RELAY
  1. Inspect the A/F HEATER relay .



NG
REPLACE A/F HEATER RELAY
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)