DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0112 | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0113 | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunctions |
| -40°C (-40°F) | Open circuit |
| Higher than 128°C (262°F) | Short circuit |
| Related DTCs | P0112: Intake Air Temperature Sensor Range Check (Low Voltage) P0113: Intake Air Temperature Sensor Range Check (High Voltage) |
| Required Sensors/Components (Main) | Intake air temperature sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor will run whenever these DTCs are not present | None |
| Intake air temperature sensor voltage [Intake air temperature] | Less than 0.18 V [Higher than 128°C (262°F)] |
| Intake air temperature sensor voltage [Intake air temperature] | More than 4.91 V [Below -55°C (-67°F)] |
| Intake air temperature sensor voltage [intake air temperature] | 0.18 V to 4.91 V [-55 to 128°C (-67 to 262°F)] |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| Result | Proceed to |
| -40°C (-40°F) | A |
| Higher than 128°C (262°F) | B |
| Same as actual intake air temperature | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect terminals M1-4 (THA) and M1-5 (E2) of the mass air flow meter connector on the wire harness side.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | Mass Air Flow Meter |
| *2 | ECM |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-4 (THA) - E5-29 (THA) | Always | Below 1 Ω |
| M1-5 (E2) - E4-28 (E2) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | Mass Air Flow Meter |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-4 (THA) or E5-29 (THA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||