AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ OFF or ON |
| - |
| SPD (NC0) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm |
| Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | 0 km/h (0 mph) (output shaft speed equal to vehicle speed): Vehicle stopped | - |
| Shift SW Status (P Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (2 Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (L Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (D Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (3 Range) | PNP switch status/ OFF or ON |
| When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted. |
| A/T Oil Temperature 3 | No. 2 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted. |
| Lock Up | Lock-up/ OFF or ON |
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd or 4th | Actual gear position | - |
| SLT Solenoid Status | Shift solenoid SLT status/ OFF or ON |
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ OFF or ON |
| - |
| AT Fluid | ATF condition/ OFF or ON |
| Replace ATF when ATF condition is ON |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLU) | Operate the shift solenoid valve SLU | OFF or ON | [Vehicle Condition]
|
| Activate the Solenoid (SLT)* | Operate the shift solenoid valve SLT and raise line pressure | OFF or ON
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate the shift solenoid valve S1 | OFF or ON | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate the shift solenoid valve S2 | OFF or ON | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid valve SLU to set automatic transmission to lock-up | OFF or ON | Possible to check shift solenoid valve SLU operation. [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (30 mph) or less |